Turbo BS Thread

Only if the seals are blown i assume

 

I need opinions on turbo blanket...

Found a t3 garret heat sheild on LCE, I'm ordering a diff drop since both cv boots are leaking so I might as well order something else while shopping it.

So think a t3 garret shield will fit a t3 borgwarner?

 

PTP Turbo blankets, is my preference. Very high quality construction. Check them out.

 

This is why certain components need to be from well renown and proven manufacturers.

I remember questioning if your injectors were at fault. Glad you found out.

These will be a bit more budget friendly than Injector Dynamics. Plus function more seamlessly.

http://www.deatschwerks.com/products/fuel-injectors

 

If I end up getting a maf sensor does anyone have suggestions on the best one to get

 

OEM, unless there is an upgrade OEM from another vehicle to yours?

 

Well, i was going to go with LCE if yall think a garret will fit a borgwarner?

If not I can get another one and just buy a supersonic bov. Might as well so shipping will be worth it....

 

It should fit. All components being similar.

 

Looks like this might possibly be the problem when I took this off to do all the checking to see what the problem was I noticed there was a film going into the intake that look like metal from this little fitting could be collecting on the map sensor I've got the correct parts ordered and on their way

 

No one ever says, "The right parts hurt." Those will at keast remove the doubts from those parts in question.

 

Exactly

 

Just ordered my next upgrade:

Tundra filters: Taller for more filters surface area

$54 Toyota Genuine Parts 90915-YZZD3 Oil Filter 1 Case (QTY 10)

https://www.amazon.com/gp/product/B00A1X9IU4/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1


Penzoil Platinum 5W-40 Euro Spec:

$45 Pennzoil Platinum Euro Full Synthetic 5W-40 Motor Oil (1-Quart, Case of 6)

https://www.amazon.com/gp/product/B00JMCCBRW/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

Spec sheet
http://www.pennzoil.com/en_us/produ...m_Euro_SAE_5W-40_Full_Synthetic_Motor_Oil.pdf

vs 5W-30
http://www.pennzoil.com/en_us/produ...atinum-SAE-5W-30-Full-Synthetic-Motor-Oil.pdf

 

I looked at there site but it appears they don't make any 5vz injectors? maybe I'd have to call
LCE makes 5vz injectors to 625cc's for $550. Id assume LCE's stuff is pretty good

 

URD might still have their injector replacement kits for the S/C. If forgot what CC they ran though. Very $$$ though.

 

Injectors here:
URD Kit - http://www.lceperformance.com/5VZ-6-Injector-Upgrade-Kit-p/1063078.htm - Expensive but you could probably sell the pump/controller seperate? Injectors are 318cc
https://www.fiveomotorsport.com/fuel-injectors/

Also IIRC, the 7MGTE injectors can work. The 315cc's are hard to find but here are some 440cc's:

http://www.ebay.com/itm/87-92-TOYOT...ash=item33ccef4c1b:g:2q4AAOSwRUhY-A3I&vxp=mtr

I'd get them cleaned though...

 

More but 550cc is pretty high...

http://treperformance.com/c-62414-f...ors-toyota-fuel-injectors-rc-engineering.html

 

Cannot go wrong with them. You know it will fit.

 

Have you checked osidetiger?

 

Thats where I got the 650's from

 

Also I knida of what something in the 600 range incase I decide to do ethanol