1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Trying to find the bolt size for the bell housing on my 3.4

Discussion in '1st Gen. Tacomas (1995-2004)' started by stuartmhill13, Aug 18, 2018.

  1. Aug 18, 2018 at 3:36 PM
    #1
    stuartmhill13

    stuartmhill13 [OP] Active Member

    Joined:
    Apr 16, 2017
    Member:
    #216431
    Messages:
    25
    Gender:
    Male
    Covington, Washington
    Vehicle:
    green 96 tacoma
    Need help figuring the size and pitch out already spent half my day looking everywhere for them
     
  2. Aug 18, 2018 at 11:05 PM
    #2
    UnderFire

    UnderFire Well-Known Member

    Joined:
    Oct 29, 2014
    Member:
    #141348
    Messages:
    451
    Gender:
    Male
  3. Aug 18, 2018 at 11:31 PM
    #3
    Key-Rei

    Key-Rei Well-Known Member

    Joined:
    Jun 20, 2017
    Member:
    #221942
    Messages:
    7,863
    First Name:
    Key
    Florida
    Vehicle:
    2010 TRD Off-Road 6Spd 4x4 209BSM
    Locker anytime Fog Lights anytime Full LED light conversion TRD cat back Rear cat delete Exaust Y reroute away from actuator Alloy Clutch master 2000 4Runner "Dog Leg" shift leaver Marlin shift seats and bushing Rear seat delete Rear diff breather extension Chrome grille swap Debadge Rear seat delete Honda blower motor beefy plug and wire mod Anytime 12v and USB with volt gauge in bed Blue Sea fuse box Hella AND 70's Caddy horns Low profile recessed hex drain plug swaps Alluminum battery strap 7pin relocated Backup cam on anytime Various other creature comfort and personal taste mods.
    Lengths vary. You can use a dowel rod inserted into the bolt cavity and marked at the level to determine length. Keep in mind bolt length will be in mm and will be measured from the underside of the head, you may also want to subtract 5-10mm to allow bolt thread headspace to accommodate dirt hole bottom taper and bolt stretch.

    Or use a web page like the below to find your part numbers and then google said bolts should net you their specific description.

    https://parts.lakelandtoyota.com/sh...1655&ukey_driveLine=6765&ukey_trimLevel=18360
     
    Running Board Man likes this.
  4. Aug 19, 2018 at 5:41 AM
    #4
    pairodice

    pairodice Well-Known Member

    Joined:
    Jul 8, 2009
    Member:
    #19456
    Messages:
    1,490
    Gender:
    Male
    First Name:
    Jay
    SF NM
    Vehicle:
    02 DCSB prerunner 4x4 manual
    Are you auto or stick? Auto uses 6 the same size, stick 3 short & 3 long
     
  5. Aug 19, 2018 at 1:04 PM
    #5
    stuartmhill13

    stuartmhill13 [OP] Active Member

    Joined:
    Apr 16, 2017
    Member:
    #216431
    Messages:
    25
    Gender:
    Male
    Covington, Washington
    Vehicle:
    green 96 tacoma
  6. Aug 19, 2018 at 1:21 PM
    #6
    pairodice

    pairodice Well-Known Member

    Joined:
    Jul 8, 2009
    Member:
    #19456
    Messages:
    1,490
    Gender:
    Male
    First Name:
    Jay
    SF NM
    Vehicle:
    02 DCSB prerunner 4x4 manual
    They are about 3 inches long, if you need an exact# I can mic one when I get home
     
  7. Aug 19, 2018 at 2:12 PM
    #7
    stuartmhill13

    stuartmhill13 [OP] Active Member

    Joined:
    Apr 16, 2017
    Member:
    #216431
    Messages:
    25
    Gender:
    Male
    Covington, Washington
    Vehicle:
    green 96 tacoma
    I gave up just set my new block on a tire I'll pick some bolts up tommorow when everywhere is open like I said it's just to bolt the new motor I have to my stand anyways
     

Products Discussed in

To Top