BUYER BEWARE: 2nd & 3rd Gen Tacoma In-Cab 120vAC 400W Anytime Power Outlet

I'd prefer all three wires go back to the inverter location if possible.
If not, no biggie.

 

I paid and responded to you message and havn't heard a word.
Motomandan
paid Paypal Dan Kenney

 

UPDATE:

Shipment will be to me in 2-3 days and then all of the orders will be getting sent out. Finally!!! I have 25 messages in my inbox still to verify and update I’m assuming all with orders and then that should be up-to-date. Now that it is the weekend, I will be starting to work on that again. Just wanted to give an update real quick with where the shipment is.

 

Is there any pictures of the bezel +outlet +usb charger installed in our truck? I saw the one pic of it installed inside of the console, but I have my CB there so can't do that...I'd like to see pics of it installed else where if anybody has some...or whenever you guys get the product installed, post up some pics.

 

I'll probably put it on the back of the console. Already have a 12v outlet there. Remove it and use the hole to start cuts.

 

UPDATE:

I have updated the list now with everyone that has PAID so far. There are 67 orders. I know there are some that are in the process of making their payments. Once you have made your payment, let me know and I will add your name to the list. You can still place an order even though you are not on the list. I just wanted to clean it all up. If you have paid and you do not see your name on the list, send me a PM. Thank You!

This is not a one time thing. I will continue to have these as long as people are ordering them. So it is never too late to place your order and get on the list. Shipment should be arriving Im thinking early this week and then all shipments will be getting shipped out ASAP.

 

Potentially dumb question:

Is the harness as it sits long enough to go from the inverter to the pocket ahead of the cupholders on a 2nd gen console?
Building a filler panel for my lighting control keypad and a few USB ports there, AC outlet would be a good addition at that location.

 

I’ll try to install it in my door panels maybe today or tomorrow

 

Can you post a pic for me and I’ll answer that question. Thank You!

 

I had a few responses that mentioned the two so I went with that. Makes it easier for Plug-N-Play. Ground wires you just need to ground to the body of the vehicle anywhere so you should be able to find a grounding location at the point of installation. However, the Blue and White Wires need to go back to the Inverter where you will connect to the PNP Harness. If you would like, I can make you a special one. Send me a PM if you are ordering an extension harness

 

Where the bank of switches are under the factory 12v ports is. I bought an 8 circuit light controller so I will be remaking the plate with a layout like this, probably moving the USB port over to the left, a 110v outlet would be a nice add roughly where the current USB port is.

 

When they arrive I can test it out. If not, you can always get an extension. Maybe I’ll offer a 3 ft extension as well. So I’ll have 3ft, 5ft, and 10ft Wire Extension

 

UPDATE:

Tracking showings delivery by 8pm this evening today on all the Harnesses If that is the case, I will try to get all of these packaged and ready to go by the morning. If you are someone that has ordered the Extension Wiring Harness, those have not been ordered yet because I wanted to have this product in hand first to see the final product and then I will be ordering those. However, I will ship these out to you now so you can get started with your install. I haven’t gotten to the install in my Rear Doors yet to show what it looks like but I will try soon. So many projects going on.

 

So who wants to buy one of these and sell it to me?

Damn prop 65

 

Well they tried to deliver the package and I was at work and it needed a signature so I missed them

 

Have it shipped to a relative outside CA who can send to you.

 

UPDATE:

Ok....well here is an update people I received the shipment yesterday after work. Very excited to open it and get started to prepare all of the shipments. However, I opened up the box to find that the Plug-N-Play In-Cab AC 120V 400W Power Outlet Harness was not correct. It was only 11" instead of 19". With that said, I'm sure you all know how the rest of the evening went. So....what will be happening!! The factory I have been told will be reproducing this Harness in one day and shipping to me directly. I should receive another update tonight. I am not too happy as this has already taken way too long. I am extremely sorry about this.

I have to go back to the east coast on Sunday evening again, but I will be back on the evening of the 10th. I'm hoping that when I return that these will be here when I get back or that they will be arriving shortly after so I can get these out to all of you.​

 

Thank for keeping us updated

 

No worries. Thanks for the update