What Have You Done To Your 3rd Gen Today?

Adjusted OEM fog lights I installed on my SR. Used scientific method, tools required:
1 - son with long arms to reach down and adjust lights from top
1 - garage door
1 - darkness
Steps: adjust until both fog lights provide even illumination on garage door, and slightly overlap the bottom of the low beam pattern. I have the full "measure this, measure that" instructions... meh. This will do for now.
Bonus- ordered some Hella H11 Xtreme Yellow bulbs for the fogs.

$23 HELLA H11 YL Twin Blister Xtreme Yellow Bulb (12V 55W), 2 Pack

https://www.amazon.com/gp/product/B079VYZ2TP/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

 

i don't have that on my windshield, unless i'm looking in the wrong spot?

or what about all the chrome buttons on the headunit? i replaced the volume/tuning buttons with the RAV4 ones to get rid of some of the headunit chrome.

and then there's the sunvisor silver screws that need replacing too...

 

Nice!! How’s ya do it? Disassemble the wheel or just pull off the emblem?

 

I didn’t have to do anything really. It’s an overlay from @AJT DESIGN. It just goes right over the existing emblem. Super easy!

 

@LSUfan1975

I hate that they were closed. At least you know how to find it!

The wind wasn't blowing so the Whirligig park was disappointing too.

 

I do believe it was a facetious reference to the rear view mirror

 

The ones Rob lists on his YouTube video for $19.99. They seem good.

 

I couldn't get mine on with both supplied washers either. I used just one washer then went looking and found this. It comes with thr thick and thin washers. Currently I have 1 thin and 1 thick washer installed and they fit perfecr with no slop or rattle. There was no rattle with a washer on just one side either

If you mean the pin didnt fit then your backets arw messed up cause 7/8" pin is what should fit

 

sheesh! that went right over my head

 

Finished up the Fox 2.0 install today with the fronts. Raised it up 1 1/4” and tomorrow it goes in for new wheels to be installed.

 

After 9 weeks of driving around with a busted up front end this finally showed up.

 

Thank you for the pictures. I’m pretty sure I can’t get these to fit with my pelfrebilt skid, but with your pictures, I can check tomorrow. Thank you

 

Picture please, is there chrome I missed someway????

Edit: it always bites me to quote and reply before I finish reading and get up to date.

Mine too.

 

Eibach stage 1 suspension lift with 1" eibach rear blocks... did the install in my garage (needed a shop to assemble the strut/spring pack), then les schwab fucked it all up with a horrible alignment (twice as I immediately went back after the truck wanted to drive itself into the right side ditch)

 

I think so too. Thinking I might of got some used ones since I bought it from directly through Amazon

I am seeing a lot bad reviews about the holes where the pin goes in

 

Extremely.

 

got me a uws toolbox today. i been hinged on the finishes prior to. originally i was gonna get the polished finish cause its so easy to maintain. the high gloss black looks good too, but truth be told when i saw the matte finish in person i was hooked. it makes the aluminum look composite and it makes the whole box look subdued. still had the hologram logo so it shimmers from certain angles lol. im not gonna use the toolbox like a traditional box and more like access storage. when the cab get full i can throw bags an extra stuff back there and keep it locked, meanwhile still have my bed for whatever arises.

 

The matte black looks great. Might paint my tool box after seeing that.

 

Nope.....one beer job

 

I want these but would really like them if they were amber. Don't wanna put the amber film on them cause after time they fade and crack.