Interior Led Problem!! Help!!

I just borrowed another 7.5a fuse and put it in the dome slot. Nothing. I'll wait and see what Caribe says. Appreciate all the help.

 

yeah I feel you. I was so frustrated!I was about to go to the "Stealer"ship to figure out what I did! where did you buy your leds? maybe they're mismatched(voltage/wattage)Is everything else working on your dash my clock stopped working & vanity lights were out too.

 

D-Lumina Compatible with Toyota Tacoma 2016-2019 LED Interior Light Kit Package - 9 Piece Bulbs (Vanity Mirror, License Plate, Map and Dome Lights) White 6000K 5050 Series SMD (2X Install Tools)

https://www.amazon.com/gp/product/B087P9H99W/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1

Everything else is working. Just dome, both map, and both vanity are dead.

 

I dont trust Amazon's this fits your vehicle thingy! the initial dome light i bought was a idlumina brand too! I think that bulb caused the problem! I just noticed that stupid "Canbus Error"warning perhaps thats causing a problem!

iDlumina Festoon 41mm 42mm C5W 561 562 563 564 566 567 570 578 6411 6451 6475 6476 7576 211-2 212-2 212-2 12V Ice Blue Canbus Error Free LED Car Light Bulb 3X5730SMD (Pack of 2)

https://www.amazon.com/gp/product/B011QV3RK6/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

 

Since you've replaced the fuse, then with a multimeter, verify power to connector R44 in the overhead console.



Slot 15, pink wire.



I'm guessing the IC module for the map lamps is burnt. Meaning you get power to the console, but this is damaged:

 

Thanks, but its all good now, all my lights are working, so far. I was just trying to help out StPete with his Led problem.
Thanks again,Caribe!

 

How difficult is it to remove the console? Do you think the dealership will replace under warranty? Truck has less than 3k miles on it.

 

IDK, yeah go to the dealer if your truck is that new should be covered...I think, call them 1st.

 

Easy removal. "Yanks" down.

 

Got it.

 

I have my first service appointment on Monday. I'll let them deal with it.

 

Isn’t technology great? All that circuitry for two light bulbs smh

 

Don't tell them what you did...just say they stopped working.

 

Not really, all the other switches and knob go through that IC board. One for some versions.

 

Not familiar with all the Tacoma wiring until I research for a mod I want to do. My SR has the light switch and a traction control switch on the overhead console, that’s it. Do you know what the chips are for? CanBus perhaps, to tell you the obvious that you have a bulb out? Lol. I presume my traction control switch goes to the ECM. I’m a design engineer for control systems (not automotive, learning here) and I stand by that circuit board is overkill, and poorly designed if a shorted light bulb can smoke an IC. ​

 

Now that’s a lot of stuff lol. Aftermarket lights too. It would be interesting to see what my SR board looks like.

 

The halves are connected with melted tabs, not really meant to be taken apart. Others have...

 

Not going to unless I have a need. Researching how or finding better ways to take things apart on the Tacoma has been a fun part for me of doing mods, like the SR Intermittent wiper mod, SR OEM fog light mod, etc. learned a lot here on TW about Tacoma wiring for those mods (some of it from you), as well as looking over the manual wiring diagrams. Up next is the keyless entry mod.

 

Back from the dealership. Blown 7.5a ECU-ACC fuse. Derp................