1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Just clamps or entire cable?

Discussion in '2nd Gen. Tacomas (2005-2015)' started by caffiend, Mar 26, 2021.

  1. Mar 26, 2021 at 6:17 PM
    #1
    caffiend

    caffiend [OP] Well-Known Member

    Joined:
    Jun 22, 2020
    Member:
    #332247
    Messages:
    144
    Vehicle:
    2007 TRD Sport
    I need to replace my battery clamps soon. Should I replace the clamps only? Or should I get entire cable with clamp? Thanks!
     
  2. Mar 26, 2021 at 6:29 PM
    #2
    joeyv141

    joeyv141 Well-Known Member

    Joined:
    Jan 31, 2016
    Member:
    #176710
    Messages:
    1,922
    Gender:
    Male
    New Jersey
    Vehicle:
    08 DCLB 4x4 V6 TRD Sport
    I assume by clamps you mean the harness battery terminals. I would just replace the ends, don't know how bad the tacoma harness is but its usually no small task to replace a entire wiring harness.
    You can get cheap battery terminals at any parts store or get nice fancy ones online.
     
    caffiend[OP] and Accipiter13 like this.
  3. Mar 26, 2021 at 6:31 PM
    #3
    Waasheem

    Waasheem The catholic radio bear

    Joined:
    Jun 26, 2019
    Member:
    #297494
    Messages:
    2,833
    Gender:
    Male
    First Name:
    Waasheem
    Vehicle:
    2007 xrunner
    Reusing cables shouldn’t be an issue if they’re in good condition. Acid hasn’t wicked up and under the insulation, not cracked or chafed or super hard, no receding insulation, and not too short to cut the existing terminals off and still have room to crimp on new ones.

    Use good quality terminals, not the cheapest ones you can find. I like the crimp on type but I’ve seen some good ones that don’t need a hammer crimp tool.

    While you have the battery disconnected you can take the opportunity to do some tests. Check ground continuity from the ground terminals to multiple places. Check coolant for electrolysis. Of course you need a multimeter and google capabilities.
     
    caffiend[OP] and Accipiter13 like this.
  4. Mar 26, 2021 at 6:31 PM
    #4
    Accipiter13

    Accipiter13 Well-Known Member

    Joined:
    Apr 5, 2012
    Member:
    #76325
    Messages:
    960
    Gender:
    Male
    California
    Vehicle:
    '11 DCLB 4x4 Sport
    Replace the terminals. Easy and cheap. Don’t bother with the cable unless you know you have damage or known tear in the insulation.
     
    caffiend[OP] likes this.
  5. Mar 26, 2021 at 6:39 PM
    #5
    Waasheem

    Waasheem The catholic radio bear

    Joined:
    Jun 26, 2019
    Member:
    #297494
    Messages:
    2,833
    Gender:
    Male
    First Name:
    Waasheem
    Vehicle:
    2007 xrunner
    Something else I like to do is clean ALL the acid off everything. Brush the posts and new terminals with a battery brush. Spray battery protector on the terminals and posts when all done.
     
    caffiend[OP] likes this.
  6. Mar 26, 2021 at 6:45 PM
    #6
    caffiend

    caffiend [OP] Well-Known Member

    Joined:
    Jun 22, 2020
    Member:
    #332247
    Messages:
    144
    Vehicle:
    2007 TRD Sport
    Thanks for the wisdom!
     
    Waasheem likes this.
  7. Mar 26, 2021 at 7:03 PM
    #7
    Accipiter13

    Accipiter13 Well-Known Member

    Joined:
    Apr 5, 2012
    Member:
    #76325
    Messages:
    960
    Gender:
    Male
    California
    Vehicle:
    '11 DCLB 4x4 Sport
    A little terminal spray every oil change will keep things looking nice.
     

Products Discussed in

To Top