Firearm BS thread

A lot of the Sheriff Deputies go see him just like I do. He tells them what he is looking for and they look at stores and pawn shops etc. to help him out. He pays cash

 

According to some interviews I’ve seen several of the manufacturers are sending mass quantities to Ukraine perhaps that’s causing some of that

 

My GM saw this at NBS and picked it up for me, he said it reminded him of me but he forgot to give it to me when he got back

 

It’s all about the girth

 

Man, I wish I lived in a community like that.

 

You can live in Georgia just need a Uhaul and a trailer for your car

 

That would be pretty sweet.

 

Come on I will show you around the whole state

 

I thought you were in CA I don't really know why

 

I have two Sisters in California. But I have always been in Fla, Al, or Georgia

 

The block ain’t ready for this heat

 

Brandon Herrera would be disappointed in you

 

Until I can purchase the AK-50 without it always being out of stock, Herrera can suck it (and I would be ok with it ). 19rds of 1-1/4oz slugs is as close as I'm gonna get. The ISC GK03++M actually does help with this disgusting Turkish recoil. Carolina Shooters for the win

 

He’s got to finish it before he can sell it and it be out of stock all the time

 

You made your

$27 bp-12 12 - silver-black polymer solar filter film sheet (12" x 12") - 1 ea

bp-12 a little bit too happy.

 

That's why its called ROCK ISLAND armory

 

I did a shotgun a few years ago with it, I loved it. I’d put that on almost all my guns if I could. It came out super clean, just make sure you clean the metal and prep it well. Of course I sold that shotgun and I don’t have any pictures of it now.


Plum Brown>Super Blue
Write. It. Down.



Found this picture on el gooble and it’s a pretty accurate representation of how the finish looked.

 

I did a thing Friday.

After being adamant in conversations with @MAG GRY TACO15 that I didn't want to modify this firearm, I've installed the Apex Polymer Flat-Faced Forward Set Trigger Kit installed in the M&P 2.0. I have not made it to the range yet, but it feels night and day better.



One thing to note, the rear sights did not slide off like they did in the install video on YouTube. After tapping them a few times and them not budging, I reevaluated things and realized the part I needed to access was not under the rear sights like it is on the non-optics ready slide. So I removed the optic and everything was right there! The striker block is what made most of the difference. If I'd have known that, and the fact that they sell just the striker block, I'd have probably stopped there.

However, having the rest of the trigger kit and the punches to proceed, I decided to carry on. I opted to use the factory installed springs, as the Apex flow chart suggests that as the lightest trigger pull. The trigger pull weight feels the same as the factory trigger, which is odd to me because it is the lightest option and the apex website says that it can reduce the trigger pull weight by 2 lbs.

https://www.apextactical.com/poly-flat-faced-forward-set-trigger-kit-for-mp-m2-0

Maybe that pull weight is reduced by the striker block? If I'd have known that I could just replace the striker block and it make such an improvement for less than half the cost, I'd have probably gone with just that.

Here's the link to just the Ultimate Striker Block for anyone else who hates the trigger on their M&P: https://www.apextactical.com/ultimate-striker-block-mp.

 

LoL, so what's the next mod?

 

Probably doing that ultimate striker block on my Shield.

Maybe saving up for a nicer red dot.

Maybe an AR-9 if I can ever wrap my head around the LRBHO and how that works.