1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

BROG Attic adapted for Access cab

Discussion in '3rd Gen. Tacomas (2016-2023)' started by Dean62, Mar 28, 2022.

  1. Mar 28, 2022 at 6:49 AM
    #1
    Dean62

    Dean62 [OP] Well-Known Member

    Joined:
    May 15, 2016
    Member:
    #187060
    Messages:
    224
    Gender:
    Male
    First Name:
    Jacob
    Florida Panhandle
    Vehicle:
    2020 TRD Sport 4x4 BR Access Cab Manual
    Thanks to Nyrob for taking the leap on this one
    upload_2022-3-28_8-35-39.jpg

    On the Blue Ridge Overland Gear Website there is a Tacoma Attic and within the description it says "Does NOT fit access cab versions of the Tacoma." which is actually lie because with about 8 more pieces of hardware it fits perfectly

    2 - M6 Rivnuts

    2 - M6 Flange bolt (Short 15-25mm)

    2 - Washers

    2 - Bolt plates with 1inch strap opening https://www.shipperssupplies.com/1-inch-bolt-down-plate

    67F4EA96-B3F6-4BBE-A85B-5B0074D2A345.jpg

    On the back wall you install it just like the directions say but with the clips pointing down instead of forward like the directions
    661921E2-3606-406D-B59A-2AE7BD61E729.jpg

    On the side just above the half doors there are black plastic covers with an opening the size of a flat-blade screw driver size hole that you will use to pry it open once open remove just like the clips off the back wall but these will not be reused.


    In the Rectangle opening is where you will use the M6 Rivnut I just tried to center so that the bolt plate covers the opening when installed

    7506C234-8127-448E-996E-2605FD86B2F9.jpg
    Once the Riv-nuts are in you will bolt in the bolt plate pointing down with a washer on the M6 flange bolt and install the sides just like in the BROG instructions where the handles would be and now you have an access cab Tacoma attic
     
    Last edited: Mar 28, 2022
    musicisevil likes this.
  2. Mar 28, 2022 at 3:12 PM
    #2
    Dean62

    Dean62 [OP] Well-Known Member

    Joined:
    May 15, 2016
    Member:
    #187060
    Messages:
    224
    Gender:
    Male
    First Name:
    Jacob
    Florida Panhandle
    Vehicle:
    2020 TRD Sport 4x4 BR Access Cab Manual
    34B5A111-050B-4848-9315-C775362A43C1.jpg
     
    musicisevil likes this.
  3. Mar 28, 2022 at 4:06 PM
    #3
    Nyrob

    Nyrob Well-Known Member

    Joined:
    Mar 4, 2021
    Member:
    #358202
    Messages:
    620
    Gender:
    Male
    First Name:
    Robert
    Vehicle:
    2021 SX 2.7 AT 4WD
  4. Mar 28, 2022 at 4:07 PM
    #4
    Nyrob

    Nyrob Well-Known Member

    Joined:
    Mar 4, 2021
    Member:
    #358202
    Messages:
    620
    Gender:
    Male
    First Name:
    Robert
    Vehicle:
    2021 SX 2.7 AT 4WD
  5. May 14, 2022 at 2:30 PM
    #5
    flatironsoverland

    flatironsoverland @FlatironsOverland

    Joined:
    Mar 7, 2022
    Member:
    #392096
    Messages:
    207
    Erie, Colorado
    Our attic kits work with access cabs, no modification necessary :thumbsup:
     

Products Discussed in

To Top