1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Fan Bracket Free Fix!!! Must Read!!!

Discussion in '1st Gen. Tacomas (1995-2004)' started by pilotj, Feb 16, 2011.

  1. Feb 16, 2011 at 3:20 PM
    #1
    pilotj

    pilotj [OP] Well-Known Member

    Joined:
    Feb 16, 2011
    Member:
    #51268
    Messages:
    58
    Gender:
    Male
    First Name:
    Jay
    Grand Mesa, CO
    Vehicle:
    2001 Tacoma SR5 TRD 3.4L 226,000 like new!
    Deck plate w/baffle, grey wire mod, defroster switch mod, LED footlights, LED cap lights, magnetic theft deterent...
    I have a 2001 Tacoma 3.4L and recently have been hearing bearing rumble near the waterpump. Truck has 210,000 miles on it. I listened to all parts with a screwdriver and found the fan bracket was rumbling like a bad bearing. The part at dealer cost is about $300. Checked online and found one for about $60. I went for the $60 part. After installing the new part, started the truck and the rumble was back with gusto!!! I could even feel the rough bearing with a screwdriver. So, I took off the new part, tapped it with a screwdriver and it went clunk.:eek: I tapped the old part with the screwdriver and it rang. The new part must be cast Chinese, including the bearing!!! :D:mad::D:mad:
    So here is the free fix:
    I have a hypodermic needle with a zerk fitting for a grease gun. Took the needle and slipped it between the seal and shaft on the back side of the fan bracket and pumped 5-6 pumps of grease into the bearing. Installed the fan bracket and started the truck. No noise, took the screwdriver and listened to the fan bracket and all I could hear was hmmmmmmm. Just like a new bearing!!!
    So, if you have your fan bracket off for any reason, at any mileage, grease the bearing and you will save hundreds!!! :):):):)
     
    Faster_n_you98 and tony2018 like this.
  2. Feb 16, 2011 at 4:50 PM
    #2
    Supra TT

    Supra TT Supercharged Lifter

    Joined:
    Jan 3, 2011
    Member:
    #48645
    Messages:
    7,228
    Gender:
    Male
    First Name:
    Eric
    Indiana
    Vehicle:
    2000 SAS D60 F/R Supercharged
    Supercharged on One Tons
    Nice work lol. Interesting.. Damn chinese!
     
  3. Feb 16, 2011 at 9:19 PM
    #3
    pilotj

    pilotj [OP] Well-Known Member

    Joined:
    Feb 16, 2011
    Member:
    #51268
    Messages:
    58
    Gender:
    Male
    First Name:
    Jay
    Grand Mesa, CO
    Vehicle:
    2001 Tacoma SR5 TRD 3.4L 226,000 like new!
    Deck plate w/baffle, grey wire mod, defroster switch mod, LED footlights, LED cap lights, magnetic theft deterent...
    I knew better when I ordered the part online. At that price, cheap is CHEAP CHINESE CRAP!!!:D
    At least they are taking the chinese part back and the factory part is like new again.:)
    I LOVE MY TOYOTA!!!! 500,000 miles, here I come! Almost 1/2 way there...
     
  4. Feb 17, 2011 at 12:04 AM
    #4
    Fati Tacoma

    Fati Tacoma Well-Known Member

    Joined:
    Apr 25, 2010
    Member:
    #35969
    Messages:
    70
    Gender:
    Male
    ok perhaps a dumb question but what do you mean you listened to it with a screwdriver? Do you just put it up against the part and the sound travels through the tool or what?
     
  5. Feb 17, 2011 at 3:23 AM
    #5
    SargeSlapnuts

    SargeSlapnuts SargeSlapnuts

    Joined:
    Jan 20, 2011
    Member:
    #49565
    Messages:
    1,285
    Gender:
    Male
    First Name:
    Nick
    Pooler, Ga
    Vehicle:
    2003 taco TRD off road 4x4 dbl cab.
    255/85-16 BF goodrich km3's, modified trail gear Bumpers front and rear, 10k winch, ranch rear lift shackles, Rancho coilovers in the front, grey wire mod, aftermarket stereo, camper top on the back.
    yes it works like a stethascope. you just put it on the part while the motor is runing and you cen hear what going on inside the motor
     
  6. Feb 17, 2011 at 4:09 AM
    #6
    Fati Tacoma

    Fati Tacoma Well-Known Member

    Joined:
    Apr 25, 2010
    Member:
    #35969
    Messages:
    70
    Gender:
    Male
    I like that trick. Thanks for the tip man. Glad you got it fixed cheap!
     
  7. Feb 25, 2011 at 8:48 PM
    #7
    pilotj

    pilotj [OP] Well-Known Member

    Joined:
    Feb 16, 2011
    Member:
    #51268
    Messages:
    58
    Gender:
    Male
    First Name:
    Jay
    Grand Mesa, CO
    Vehicle:
    2001 Tacoma SR5 TRD 3.4L 226,000 like new!
    Deck plate w/baffle, grey wire mod, defroster switch mod, LED footlights, LED cap lights, magnetic theft deterent...
    500 miles since greasing the fan bracket.
    Listening with the screwdriver, it still sounds like a new bearing!
    Guess I'll grease it again in another 100,000 - 200,000 miles....
     
  8. Feb 25, 2011 at 9:18 PM
    #8
    NegroTundra

    NegroTundra Well-Known Member

    Joined:
    Oct 25, 2010
    Member:
    #45227
    Messages:
    651
    Gender:
    Male
    Land of Enchantment
    Vehicle:
    03 Tacoma TRD 4WD 5 spd
    You gotta pic of exactly where you put the grease?

    Great fix btw. Mine has been calling crickets every since I bought it.
     
  9. Feb 26, 2011 at 8:11 AM
    #9
    pilotj

    pilotj [OP] Well-Known Member

    Joined:
    Feb 16, 2011
    Member:
    #51268
    Messages:
    58
    Gender:
    Male
    First Name:
    Jay
    Grand Mesa, CO
    Vehicle:
    2001 Tacoma SR5 TRD 3.4L 226,000 like new!
    Deck plate w/baffle, grey wire mod, defroster switch mod, LED footlights, LED cap lights, magnetic theft deterent...
    I didn't think about taking a pic when I had it off.

    You need to remove the fan bracket first. Very easy, just slack the p/s and alt belts, remove the four nuts attaching the fan,
    Remove the fan and pulleys,
    Remove the 5 bolts attaching the fan bracket and remove the fan bracket,
    On the back side of the fan bracket you will see the shaft protruding from the seal.
    Carefully insert the grease needle between the shaft and the seal, then pump 5 or 6 pumps of grease behind the seal. This is a two person job, because you won't be able to get a good seal on the needle without two hands.
    Be sure you have the grease gun needle that is like the one pictured.
    After greasing, rotate the shaft, you should feel the resistance of tbe grease, if not, add more grease.
    Then reinstall and your done!

    IMG_20110226_100802.jpg
     
  10. Feb 26, 2011 at 8:20 AM
    #10
    pilotj

    pilotj [OP] Well-Known Member

    Joined:
    Feb 16, 2011
    Member:
    #51268
    Messages:
    58
    Gender:
    Male
    First Name:
    Jay
    Grand Mesa, CO
    Vehicle:
    2001 Tacoma SR5 TRD 3.4L 226,000 like new!
    Deck plate w/baffle, grey wire mod, defroster switch mod, LED footlights, LED cap lights, magnetic theft deterent...
  11. Feb 26, 2016 at 2:22 PM
    #11
    tacopablo

    tacopablo Well-Known Member

    Joined:
    Nov 22, 2015
    Member:
    #170400
    Messages:
    103
    Gender:
    Male
    Québec
    Vehicle:
    2002 tacoma 2.7l
    Hey Jay, I have the same problem here with my 1998 v6 tacoma with 333 000 km on it. I'll sure try your trick before buying another over priced part.

    Thanks for your post!
     
  12. Feb 27, 2016 at 10:16 AM
    #12
    Dirty Pool

    Dirty Pool FLIES ON THE FRIES, KETCHUPS WATERED DOWN

    Joined:
    Mar 24, 2013
    Member:
    #100471
    Messages:
    2,261
    Gender:
    Male
    59.4 Miles, 56.67° NE Of Moab
    Vehicle:
    99 XCAB V6 MT TRD
    Dirty Pool rear bumper/air tank with integrated spare CV shaft storage, DP customized TJM front bumper, 8000 lb Ramsey/Technora rope, E-locked, Extended breathers with front diff catch can, PCV catch can, SAWs with DP heim joint seals, DP custom 6 leaf rear springs/Billies, DP custom skids, 2lo, Gray wire, Cap, Bed Rug, Black steelies, 01 Center console, Map lights, Disraeli gears
    Once the bearings have been run dry they have been damaged. Adding more grease may quiet things down, for a while.
    This is the proprietary bearing assembly, 1 row of ball bearings and 1 row of rollers. Just so you will know what your sticking a needle into.
    FSBBR_zpsoqff2brh_b95094798494c5f3731aabe4773b0c13e2498b0a.jpg
     
  13. Feb 28, 2016 at 12:44 PM
    #13
    tacopablo

    tacopablo Well-Known Member

    Joined:
    Nov 22, 2015
    Member:
    #170400
    Messages:
    103
    Gender:
    Male
    Québec
    Vehicle:
    2002 tacoma 2.7l
    Thanks for the advice, I was looking for a short term repair. But I just started the engine and that was not the problem -_-'
     
  14. Feb 29, 2016 at 11:17 AM
    #14
    Trapperr

    Trapperr Well-Known Member

    Joined:
    Mar 6, 2014
    Member:
    #124720
    Messages:
    1,002
    Gender:
    Male
    Reno, NV
    Vehicle:
    2002 Tacoma Double Cab 4x4 3.4l V6
    after changing my timing belt and water pump last weekend I have a metal on metal sound that sounds like it's coming from my fan bracket. I had grayish black shadowing on the back side starting at the bearing and spreading out like the bearing puked it's grease. I sprayed it down with super clean and washed it down which I now regret. Think I got some degreaser or water in the bearing. Ordered another bracket online ($107) and I'll put it in when it arrives in a few days.
     
  15. Jan 27, 2019 at 12:51 PM
    #15
    CrippledOldMan

    CrippledOldMan Well-Known Member

    Joined:
    Jan 25, 2019
    Member:
    #280651
    Messages:
    2,110
    Gender:
    Male
    First Name:
    David
    Salisbury North Carolina
    Vehicle:
    2003 TRD Crew Cab
    None
    I've used a piece of wooden closet pole for the last 30 years to listen to bearings, and other weird engine noises. put on the valve cover and listen to lifters etc. sound travels very good through wood, and if it gets dinged up, it's cheap to replace.
     
  16. Jan 27, 2019 at 5:39 PM
    #16
    1997tacomav6

    1997tacomav6 V6 5sp,RegCab,TRD Supercharger,Haltech,meth, 750k

    Joined:
    Oct 5, 2013
    Member:
    #113940
    Messages:
    10,231
    Gender:
    Male
    First Name:
    John
    Denver
    Vehicle:
    97 reg cab, v6 5sp 300hp supercharged, Methonal Injection, 750,001 plus miles, Original Owner
    V6 5sp,RegCab,TRD Supercharger, 1.9” pulley, methanol injected Haltech ECU, AC TRD supercharger,(MUST DO) TRD supercharger ported, every 125,000- 150,000 needs rebuild Projector headlights HID 5 speed manual Amsoil for all drive train Smaller 2” pulley, (MUST DO) 2004 DESNO fuel injectors, zero ping ping, 2004 side door mirrors Dick Cepek Rims, Michelin tires LTX, ( that last 100,000 miles) Now running Dynopro ATM mud and snow tires KN cold air intake Cat back exhaust with ss exhaust tip, Raised exhaust tail pipe to 2" below body line Optima*dry cell battery,red top Alpine sirius radio, 200 watt amp, focal is165 split door pod speakers Focal door speakers Subwoffer behind seat Viper alarm, Electric Locks Dark tinted windows, bucket seats corbeau lg1 Tacoma Rubber floor mats TRD fender extenders, Bilstien shocks, King shocks nerf bars, add a leaf for rear springs trailer iv hitch, electric brake control, Drilled slotted brakes, High carbon steel (MUST DO) EBS green stuff 7000 series pads(MUST DO) TRD engine oil cap TRD stick shift, Marlin crawl shift kit. Rear sliding window 2002 4Runner functional hood scoop cut into Tacoma hood, 4Runner dual overhead map light Gentex Auto dim + Compass + Temp, garage,rearview mirror Snow Methonal kit stage 2 Custom 3 core aluminum radiator Linex bed liner Haltech stand alone ECU, Intake supercharger gauge. Stainless steel brake lines, Custom leather wrapped steering wheel,
    If that trick doesn’t work, rockauto has Asian ones for around 100.00 that work great.

    3ED28AA9-ADCC-4608-89A3-DBF5A71C2DF4.jpg
     
    tony2018 likes this.

Products Discussed in

To Top