What Have You Done To Your 2nd Gen Tacoma Today?

I like them alot! My only gripe, although very small, is that once I removed the plastic tops they revealed some marring/scratching where it was covered before. Some will buff out, but in my particular case I had some fairly deep scratches that I had to use touch up paint on. Not a deal breaker by any means.

Just a heads-up, kbvoodoo is making some more storage space for other products and there's only a limited supply left. Get em now while they're available.

 

That looks so good!

 

I just tallied everything up from my Amazon history. Everything you see even down to the screws came out to $260. Big savings if you’re willing to grind it out.

Granted, this is iteration #2 since my first design was poo poo. It was unorganized, sloppy, not waterproof, and the wiring was too small. Probably lost $50 worth of materials by starting over but I’m very very glad I did.

 

Why'd you drain the tranny fluid to begin with? And the blower motor and resistor are extremely easy to do, but I agree the peace of mind is good. I've replaced my blower twice, and the resistor once.

 

This looks solid. I need to do this. Are car washes n such not a concern when the water goes down the windshield?

 

Because it was recommended by Toyota to do it every 60k miles, and when I bought the truck with 80k miles, I wasn't sure if it had been done or not. I'll keep that mind if my blower ever acts up again.

 

Arches Nat'l Park last summer. Was only 105 that day so not bad.

 

Broke out the old Taco for my daily again today. Gave daughter a good deal on my old 2003 Camry, with 98k miles, for my 16 year old grandkids 1st car. Not sure who is happier. I will miss the Camry but the Taco has looked sad and lonely mostly sitting for a few months.
Now 2, of my 3, kids, my parents and my grandkid are in Toyota vehicles.

 

Not really. Cowl cover redirects most of the water to the sides of the windshield and the HVAC inlet cover redirects anything that may get through

 

this is exactly what I want to do with mine, Any issues running the cable from behind the dash up to that point?

 

Do you recall what size hole saw? (Firewall)

 

Progress pics of the truck so far. Cant wait to get it back.

So far they've done all the engine work (new csf radiator, thermostat, water pump, URD cam gears, intake manifold spacer and regular maintenance).

Currently working on the front end (bumper, lights, suspension refresh)

Afterwards, they'll start on the rear end. (new carrier bearing, inspect u-joint, weld shock relocation and install suspension)

Once the truck is back, off it goes to get regeared and add a e-locker.

Diode Dynamic fog light w/backlight on


Fog lights on


Light Bar on.


and the new radio.


My old pioneer kept acting up so best buy sent it out to have it inspected. Came back faulty so they gave me store credit. Picked up a new 75 inch tv and sound bar. Only paid for delivery and set up out of pocket.

 

The third brake light on my shell filling up with water, time for a replacement. The stock ARE light was UV damaged front and rear.



Not wanting to shell out $50 for a stock replacement, if I could find one, I rolled the dice and went for a $10 eBay high performance special and $10 worth of silicone seal. The eBay light is nice and bright, I like the red better than the clear with red LEDs, but of course, it did not fit properly. Classic one size fits all but actually fits none but pretty close in most applications.



Liberal application of silicone sealer on the back seals a 5mm gap on the back, but it sticks out about that much on the bottom. If it lasts for awhile I can forgive the fact that it looks like ass.

 

Take a look at this post: https://www.tacomaworld.com/threads...-and-hvac-screens.811746/page-3#post-29174084
The cowl cover holes don't allow water to get into the HVAC area. Make sure the cowl cover seal that is against your windshield is in decent shape because that is the only way water can get in.

This is the seal I'm talking about.

3-1/4" diameter.

 

Got the space frame welded up for the Ripcord DIY camper build. Just need to add the angled supports and can start ordering the extrusion

 

Crossed a milestone today!

 

Installed these to go along with my Brite box with fog light control.

 

Where did you get the yellow film and do you like the result? I’m looking at doing the same thing, or possibly doing part of the light bar in my front bumper.

 

Got the lid back from powder coat this evening. Got it re sealed and riveted back on, looks great. It got dark on me, so I'll post some pics tomorrow.

 

I had to run the wires on the front of the dash. I wanted to run them under the seal at the door but the harness was too thick. I’m not happy with it, but nothing is pinched or stretched. I’m sure I could make it neater, but I was running short on time!