FS: Rear Seat Delete Deck for 4th Gen Tacomas (Double Cab)

FOR SALE:
Rear Seat Delete Deck for 4th Gen Toyota Tacomas
(Double Cab versions available)


Rear Sear Delete Deck (for 4th Gen Double Cab) assembled.



Rear Sear Delete Deck (for 4th Gen Double Cab) installed.


Perfect for dogs or other wild beasts. Can even be used to secure tools or other precious cargo. Perfect surface to mount your refrigerator to for camping/overlanding.

​

Inspired by the rear seat delete thread found here: https://www.tacomaworld.com/threads/rear-seat-delete-decks.632134/ I have designed and made my own version using a CNC. After posting my RSD Deck, I have had a lot of interest, so I have decided to go ahead and offer my version for sale, along with designs for 4th Gen Double Cabs.

Each RSD Deck is made to order and usually ships out about a week or two after payment is received. This Rear Seat Delete is designed to work with the factory panels located behind the rear seat. It is also designed to be easily installed for the weekend or permanently installed depending on your needs.

This RSD Deck kit is part PRO part DIY and must be assembled, sanded, sealed and finished by the buyer. All parts parts have been CNC'd and pre-drilled for easy assembly. Hardware not included.

At this time this RSD Deck is ONLY available for 4th Gen DOUBLE CAB. Access Cab designs are pending as soon as I can get access to one.
Unfortunately, a cubby delete version or a 60/40 split version cannot be produced at this time.


FEATURES:
Dimensions: About 53" wide X about 28" deep X about 12" tall (Double Cab Version)
Materials: 3/4" birch plywood
Shipping: Ships to lower 48, un-assembled in a crate (54 x 34 x 2 inches - 40lbs) *Can ship to Canada for additional cost.
Assembly: The deck will arrive in 14 pre-cut parts. All holes come counter-sunk but must be pre-drilled before screwed and glued together. Please use 1 5/8" screws and wood glue (both not included). This must be assembled, sanded, sealed and finished by the buyer because building stuff is fun.
Finish: Your choice of Monstaliner (roll on) OR Raptor Liner (spray) OR Automotive Carpet, or however else you envision your RSD Deck to be finished.
Cargo Hatch Lids: FOUR Cargo Hatch Lids are included in this kit. The front two lids open to the area where one's feet would be, if sitting on the rear seat. The rear two lids open over to factory cargo area. The lids are latched in place by the use of magnets (not provided). To open the cargo hatch lids, simply slip your finger in the pre-cut finger hole and pull up. To close: simply place cargo hatch lid in appropriate space and magnets (must be purchased and installed by buyer) will hold lid in place, securely.
Installation: Remove rear seat and tuck rear seat belts out of the way or remove (preferred). This removal process takes about 20-30 minutes. The RSD Deck installs into the Tacoma cab assembled and is designed to follow the contours of the floor of rear of the cab. Can be installed for the weekend by letting it sit in place under its own weight OR can be installed more permanently using angle iron or L brackets (not provided) and piggy back the rear bolts of the front seats. (Please see image 6 this post for inspiration: https://www.tacomaworld.com/threads/rear-seat-delete-decks.632134/#post-21691175 )


PRICE:
Cost: $775
Shipping: additional $120 (Includes crating, packing and shipping to anywhere in lower 48 states) *Will ship to Canada for additional Cost
Payment: Venmo is preferred.


ORDER:
DM and we will get things started.

Once payment is received in full, your order will be placed in the queue.

Sorry, no refunds.


NOTE:
The Rear Seat Delete for 4th Gen Double Cab includes an additional brace beneath the main platform compared to the designs for the 3rd + 2nd Gen's. This brace must be installed first before the other parts. The orientation of this brace is specific and must be installed facing the front of the cab as indicated by the engraved text "FACE FOWARD".​

​

To install the brace, flip the main platform upside down, revealing the dado'd channel. Slide the Brace into this channel and glue, pre-drill and screw into place (from the top of the main platform).

​

​

​

​

​

​

​

Once this brace is properly installed, proceed with assembly as instructed for the design for 3rd + 2nd Gen Double Cab Tacomas.
​

​

**INSTALLATION NOTE: SUPER IMPORTANT!**​

When installing the Rear Sear Delete into the 4th Gen Double Cab, YOU MUST first adjust the resting location of your factory provided bottle jack. As installed from the factory, the bottle jack will interfere with the back edge of the REAR SEAT DELETE. Shift the location by simply loosening the bottle jack and push towards rear of the cab. Once shifting the resting location of your bottle jack, tighten it back up and proceed with the installation of your Rear Seat Delete.
​

​

DETAILS of DESIGN:
The Rear Seat Delete for the 4th Gen Double Cab has to contend with a number of factors that aren't included in the 3rd + 2nd Gen Tacomas. This Rear Seat Delete is about 5" taller than the design for 3rd + 2nd Gen Tacomas due to additional safety features welded to the frame AND Toyota's different design approach.

It appears that the rear under seat storage compartment of various 4th Gen Double Cab models are different in detail, compared to each other. It has been confirmed that though there are differences, the Rear Seat Delete will work with all of the rear under seat compartment designs. Please see the two photos below and compare.
​

2024 Double Cab 4x4 Tacoma


2024 Double Cab 4x2 Tacoma​

Additionally, in order to fit properly, the Rear Seat Delete for 4th Gen Double Cab Tacomas is designed to sit slightly inset compared to the outermost edge of the rear under seat storage compartment. Please see photo below for the reveal.
​

​

Lastly, the rear "fin" of the this design is optional and can be installed or omitted per the buyer. Every kit will include and will ship with the rear fin but it will be up to the buyer to install it or not.
​

​

FAQ:
1. Do the front seats slide back all the way with this RSD Deck installed?
• Yes

2. Is this RSD Deck just set in the truck, or how is it bolted down?
• Designed to be "set" in the truck but can be easily modified to be permanently installed at your discretion.

3. Do you know if this RSD Deck will fit for those with a factory sub enclosure behind the rear passenger seat?
• Yes it will work with factory sub installed (verified in 3rd Gen Tacoma).

4. Will this RSD Deck still work if I wanted to remove the rear factory panels anyways?
• Yes! It will still fit just fine. In fact, one of our customers has done this and replaced the cubbies with a molle system.

5. How long would it take you to create the kit and get it in shipped?
• After payment is received, it takes about a week or two, to CNC mil and pack the RSD Deck. Shipping normally takes a few days to a week.

6. What shipping company do you use?
• UPS via Shipnerd.

7. Where are you located? Can I pick up if local instead of paying for shipping?
• The shop is located in Los Angeles. If you would like to pick up, then we can arrange that.

8. What is the preferred method of payment?
• Venmo

9. Why does the RSD Deck for the access cab costs the same price as the one meant for a double cab?
• Even though there are slight variations when comparing the two RSD Decks, the material needed for both designs is practically the same as well as the time on the CNC machine. Material and CNC Time are the two main factors that determine the price.

10. What determines the price?
• Cost of materials which have increased due to pandemic. Not to mention the cost of running the CNC and the time it took to develop this quality design.

11. Can I order a custom RSD Deck?
• Unfortunately not at this time.

12. Are assembly instructions included?
•No. Please visit this link for assembly instructions: https://www.tacomaworld.com/threads/rear-seat-delete-decks.632134/page-12#post-25588580

11. What other items do I need to purchase to assemble this RSD Delete?

ASSEMBLY:
• Wood Glue
• 1 5/8" wood screws
• Sand paper: 80, 120, 220 grit
• Bondo: All-purpose Bondo (no affiliation)
• Oil Based Wood Sealer: Minwax Oil Based Polyurethane (recommended - no affiliation)

FINISHING:
• Finish coat: Monstaliner or Raptor Liner or one of your choice
• Magnets (for cargo hatch lids): (48) 6MM WIDE x 8MM TALL Magnets similar to these (no affiliation)
https://tinyurl.com/k4zh7wkr
• Super Glue or Epoxy
• Tie-Downs (if wanted) such as these (no affiliation): https://tinyurl.com/ddv6aeeh
• If you use the recommended tie-downs, then you must purchase (4) 1/4-20 x 2" flat head bolts

13. Which material do you personally recommend to use as a finish for this RSD deck?
• I personally used the roll-on bed liner by Monstaliner. I did have an issue as one of the pints arrived expired, which gave me some issues when rolling it on. (I didn't know it was expired until after the fact). Monstaliner was quick to replace the pint, however, I had to put in some extra effort to remove the expired coating. In the end, everything worked out. I have used Raptor Liner on other builds. It's good. A little more difficult to control the texture of the final coating compared to Monstaliner, but that's just my experience.

14. What cargo hardware do you recommend?
• I recommend these: https://tinyurl.com/ddv6aeeh If you use these, you will need to purchase (4) 1/4-20 x 2" flat head bolts

15. Can I pay for you to assemble and finish the RSD Deck? Can you ship it finished?
• No.

16. Will you ship to Canada?
*Yes, for additional cost.


​

THANKS IN ADVANCE FOR THE INTEREST!​

​

 

*bump*

 

Bump