What Have You Done To Your 3rd Gen Today?

Yep, up the drain hose. Passenger side front fender area behind the flap. Half a can, then let it sit until it drains, then the other half of can.
Recirculate button off, cabin air filter out. After that select face vents, face feet vent combo, and defroster for about 30 seconds each while blowing full speed. Add ozium to intake vents under hood by the cowl during this process. Install a new cabin air filter once process is complete.

edit: you'll want to pinch the drain hose around the ac coil cleaner hose as your injecting it so it shoots up to the coils and doesn't leak all over the ground.

There's a few YouTube videos out there...

https://www.youtube.com/watch?v=JNRznrMivn0&t=393s

https://www.youtube.com/watch?v=eRy23TFpM4I

 

After the kwikfab internal stiffies, I reinstalled my slide and fridge. Plus got a tonneau cover to hide said fridge from, well everything. Had to rerun some bedlights and the rear facing lights to accommodate the tonneau. I love this tonneau cover. It’s sleek, real low profile. Washed it, drove it dry.

 

That fridge is really nice being super low profile and having a drawer.

 

The drawer is really nice but it’s pretty unprotected. I built a box out of abs and reflective bubble wrap

 

I can see why they built the box in the pic I just added above now.

 

im doing mine now, what did you use to secure the fridge slide to the bed?

 

I have something similar to this

$141 US Cargo Control L Track Tie Down System, Includes (2) USA Made 4-Foot Black Anodized Aluminum L-Track and (4) Black Single Stud O-Ring Fittings, Trailer Tie Down System for Trailers and Truck Beds

https://www.amazon.com/dp/B00NUU4A3K
but I bought it direct from the website. That’s in my truck bed. I used one of the bolts as opposed to eyelets to secure a bracket I built with extruded aluminum and 2” aluminum stock for the fridge.

 

Can I ask where you got the dash pad and how well does it fit, does it sit into place or is it held down with sticky stuff?

 

All that you need now are some FJ Cruiser cup holders

Available on Amazon 2 for $10.00

 

I was contemplating installing some of these. Going camping this weekend, so i'll see how it works without the cupholders. i sleep with the tailgate down and have to crawl/walk on it so i would hate to pop one of these in there, and kneel on it causing it to break.

Obviously rigorous testing with a 30pack will be conducted. Pics to follow.

 

I like your style.... Perhaps with the remnants from your panel, you could create something like this.

 

Depending on the depth you might be able to put the stainless steel cup holders in like we have in our boat.

https://a.co/d/iImjtjn

 

Low actually, just under 12,800 miles. Well below the Toyota recommended 30,000 for normal driving.
I had heard that factory fill was often a little low due to the various diffs they put in. A little less than 4qts came out of a 4.2qt diff, with a long drain time.
I was disappointed with the quality of oil that came out considering its lack of abuse.
I'm in the process of going through and checking/changing out all the factory oils as a precautionary measure.

 

Have not set it up yet, but found a right line gear tailgate canopy on clearance at fleetfarm last night. Should make a good addition for tailgating for my daughters dance team.

 

Would you want them draining into the tailgate though?

 

Is not hard to either seal the hole or use the fittings they come with that accept plastic pipe to drain them externally like you're supposed to on the boat.

 

i would be getting the solid bottom, no drain. There's enough room for the deep/standard style cupholder, but I will likely get shallow ones. easier to clean out.

 

No today, but yesterday some early morning trail action. Great views.

 

153!!