FS Turbo 05 OR Prerunner (piston #6 cracked) $6k OBO local pickup only

My intercooler filled with condensation as my truck sat for a Year and I didn't find out until it was too late... I ran an unknown amount of water through the intake and seemingly bent the rod on cylinder 6 which allowed the piston to contact the counter weight at a speed fast enough to create a hairline crack... At any rate. I have torn into the engine as far as I want and don't have time or not to put it back together. $6k is basically what I have in the turbo set up and I'm giving away a truck and extra set of wheels. This would be perfect if someone is looking to turbo their current 1gr and wants a spare engine to build up with forged internals. I'll do my best to list the details, but it's all in my build thread if you need any more details.
Truck has ~260,000 miles
BW s256 turbo
All hot side, cold side and exhaust was fabbed by me and my neighbor, the up pipe may need a redesign unless you don't mind trimming a little sheet metal in the fender well.
255 lph deatchwerks fuel pump
650 cc injector
Mapecu3 piggy back
Street tunes on e85...
In addition to all of this, it also comes with two cardboard boxes full of parts that I have taken off in attempts to reconcile the issues (cam shafts, various bolts and nuts, oil pan, intake plenum etc).
It has the stock OR wheels and a set of stock 3rd gen wheels.
Post Turbo is a 3" stainless exhaust with resonator and chamber muffler dumped in front of rear passenger tire.
Ideally a standalone AFR gauge, external map sensor, and ethanol sensor should be installed and ran in conjunction with the mapecu, I just never did.
I'm sure I am forgetting stuff but as I said, feel free to thumb through my build page, and of course I can help you load it on your trailer when you get here
It has Bilstein 5100 with stock springs set at 1.75" that have approximately 75,000 miles on them, and I sprayed raptor liner on the rocker panels and fender flares and the bed 13 years ago.
https://youtu.be/JoJi9Pumygg?si=Ky6QG4hVBNkxq8ii

 

Dope

 

Bump... IC full of water https://youtube.com/shorts/zkefwbUAZEI?si=a-3lKVcdSTGti4yN
Muffler setup

 

Bump... They are pretty nice cardboard boxes js

 

Bump

 

Bump

 

This would be fairly tempting if I wasn't up in WA, GLWS though

 

Real estate is reasonable down here, js...

 

I have absolutely zero need for this but i'd be lying if i said it wasn't slightly tempting, especially since I too am in North AL and have a 1GRFE that could be put back together and slapped in there...

Any desire for a good short block and refreshed heads that just need to be put back together??

 

I have reached my desire capacity for reassembly lol

 

i feel that lol one reason of many i replaced mine

where in north al are you

 

I'm about 10 miles west of hartselle, you?

 

if i get an itch up my crack and decide i want another project... ill let you know

 

Nice turbo manifold(s) !

That alone is almost worth a huge chunk of OPs asking price.

 

Bump

 

Both set of wheels bump because I'm sure that will be what puts someone over on this buy...

 

Bump

 

Man this is very temping. What part of north Alabama are you in? I’m about 3 hours from Decatur.

 

I'm 20 minutes south of Decatur. A little dot called Danville

 

Even better thats only like 115 miles from me! I am going to see about renting a trailer and if I have somewhere to put the truck haha. I’m currently living with my brother so space is limited but its hard to turn down this deal