Tractors, Mowers, Chippers, Trailers, Chainsaws, Generators, Driveway Erosion Control, ETC.

I see it often, too. It's either the connector is not snug anymore and all the vibrations cause it wiggle thus the current can only flow thru a small section of the terminal and builds up heat.

Or the clutch itself is wearing out and the magnets are working hard.

When those connectors go bad, I cut them off and just install female spade connectors and heat shrink them good so if the wires come off and don't arc.

 

That's what I told him I would do tomorrow, got some connectors at home. Thanks!

 

These are the terminals I use. They are crimp on connectors.

This pic just shows the wire side heat shrank. Once you heat both male and female sides and the middle, the connection is very weather resistant and difficult to pull apart.

 

Check out this hot mess!



Mating a JD 757 Z Track to a Predator 670.

JD doesn't use colors to keep the wires organized. They use small numbers to label the chassis side wiring. No joy!

Spent an hour wiring up a temporary wire harness to make both sides play nice.

JD schematic is useful, but I much prefer different colored wires like Kohler does.

 

"JD doesn't use colors to keep the wires organized. They use small numbers to label the chassis side wiring. No joy!"


Kirk said "I can top that, I'll use all blue wires"

I am impressed with the projects you take on, and make work

 

https://getyarn.io/yarn-clip/116d8474-7a3d-4a38-91a4-79fd5721248b

 

did some more for the neighbor this morning... still didnt take any pix. i just get so focused on what im doing that pix dont happen.

 

It's offical Gator G5 blades are my goto blades. They have handled everything I've thrown at em.

 

Yea they’re the goods. When you sharpen them be sure to sharpen the upturned fins also. You don’t gotta razor sharp them just keep them crisp square. I have the heavier duty G6 gators and they are the only blades I’ll use anymore.

 

Well this was fun. Nice little flash flood. We had one two years ago but this was was worse. Got an inch of rain in 10-15 minutes and it just all funnels down the hills behind our property. This one would have been worse but after the last one we rented a mini excavator and dug a 12-18" and banked the dirt to create a trench and berm. It took a lot of the water but eventually a portion failed and washed out (the berm not the trench)

Thankfully our house and the big shop are elevated enough to not really be in any danger. But our "small garage" got flooded. Was about 4" of water in it plus all the silt and mud so thats fun. The yard also had some of the dirt and road base/rocks wash into it a bit but overall thats not to bad. Just going to be some cleanup of that silt/mud.

O and our bank to the irrigation ditch took some damage so we will have to evaluate that but we didnt really go over to it. And our road had some o fthe road base/gravel wash off but thats an easy enough fix to not really care. Already went out and fixed a couple spots with the back blade

 

Yesterday and today pressure washed my mother's house and our house. Simpson pressure washer with the Honda engine.
And weed wacked this morning after mowing yesterday.

 

I'm back to making "donuts" (many of you may remember the "gotta make the donuts" reference). And, so that means I get to hang out with you guys again. A weekend of cookouts, fishing, yard work, and sleeping. I liked it. Stayed away from any news and bs in the world.
Question: I was always told that when you fly in a CH46 (now retired) and you see the flexing and leaking inside as you sit there....it's a good sign since it shows that it has hydraulic fluids. Crazy right?
So, when should I worry about hydraulic fluid leaks in the BX23S? I noted a steady stream as I put the back hoe back on as I drove to my shed, but after I shut it down and inspected (and started back up) it stopped leaking. Guess I need to have it checked out.

 

What do you mean by “put the backhoe back on” ?
Are there quick connect lines you take on and off? I’d check there for any leakage first if you haven’t already. Improperly seated couplers can and will leak.

 

May have had a piece of dirt where the o-ring met and sealed itself off or something. If it ain't leaking now, don't mess with it

 

on the kubota bx, you can detach the backhoe in no kidding less than 2 min. It has quick connect couplers and I do know it sometimes can be an issue (flat face coupler) where the gasket is on the inside can sometimes get stuck open if not properly seated. So, I'm guessing I will leave it be and see if it happens again.

 

Broke another Cub cadet throttle handlejunky plastic parts @Delta09

 

Tie a string to it and run it wide open

 

Bout to. I barely bumped it getting off the mower broke the handle flush

 

Scrub Cadet doing Scrub Cadet things