What Have You Done To Your 2nd Gen Tacoma Today?

well done, and deja vu (IG last evening or this AM)

 

Ah that makes sense, thanks!

 

Catch up post!
Bedboxes/sleeping platform (earlier this year)
Clazzio Seat Covers (awesome, just recently)
Cobra CB with Firestik (Fire Stik not shown, recent)
Finished up rear seat delete and molle panel (needs trim, just recent)
Replaced head unit (older)
grab-handle phone mount via Ram tutorial from Mods sticky (just finished but not pictured!)
New front rotors and brakes (Power stop, just finished!)
New Driveshaft (just recent, need to adjust angles)
Small boi radio antenna (recent, of course it's right next to the Fire Stik, lol)

Lots of other small stuff over the last couple of years to make lift and life work a little better.

Next on agenda? Swap armrest cloth to leather, trim out molle panel, finish carpeting in cap (add light), rewire second battery for bed and add power box, need lighting (open to suggestions), finish paint on bed boxes and carve out openings for 2nd battery access, mobile water solution, dynamat doors/floor/roof, fix paint on roof, require hitch, fix cap brake light, hood struts, general maintenance overhaul (just hit 130k!) when does it end? (hopefully never)

Cheers!


Any good wheeling suggestions in Maine?

 

Nice upgrades!
What kind of driveshaft did you pick up?

 

Thanks!

I ended up with this two piece drive shaft from Extreme Terrain's site: https://www.extremeterrain.com/tacoma-rear-driveshaft-prop-shaft-assembly-apds0247.html . Super easy installation and bolted right up (took longer to unbolt the old one than to get the new one on. No complaints.

Wanted to go with a Tom Wood's single piece but it looks like they've discontinued and the Knoxville version is roughly $1200 (yikes). That, and if I was required to pull measurements on it i'd definitely mess it up!

 

How are your pod lights mounted up front? Love the look of the new grille.

 

That’s slick. Where’d you snag that from?

 

Where'd you get that "sticker"? I have paint coming off in the same area and would like to fix it then apply some type of protection.

 

I think it had an STD... it was crusty!

 

after I mounted mine I thought about putting it in that garage door opener spot, could have done the 8 spot one even.

 

Damage while wheeling...Broke my driver parking brake and destroyed wheel cylinder leaking fluid over everything. Damaged backing plate as well. Once repair was completed brakes would not hold pressure and found that brake master cylinder damaged.

So replaced driver wheel cylinder, backing plate, wheel bearing, and parking brake. Replaced brake shoes and hardware on both sides. Replaced brake master cylinder and reservoir.

 

That's some serious wheeling!

 

Replaced the rear amber turn signal bulbs (Sylvania) with VLEDS https://www.vleds.com/3157-50-hv-amber-2.html and the VLR6 resistors, found the stock LED brake and turn signal center contains a circuit board running all those center LEDS, and I'd replaced the reverse bulbs earlier. Unpacked a Cat-branded All-in-One jack this afternoon that I'd ordered Monday from Northern. 21" maximum height with a 12" square flat steel base will handle more with a couple 6x6 blocks next to each other. This morning, I had my semiannual dental appointment and met the clinic's new hire, Dr. Jack. He looked at my latest digital X-ray photos, and remarked that my teeth are in better shape than his. Not bad for this 70-year old guy, and we share similar northern European ancestry, all mixed up. Yeah, probably nothing we'd want to learn by having that tested . I think I figured out how to release the electrical connector for the front turn signals, and for the side marker lights? There's always another day...

 

Picked up these Yakima ski racks. Wanted to use them on my camper shell with my front runner roof rack. Since I have a baby 5' bed

Found some extra mounting feet and drilled some holes that way they fit with my rail system.

 

ARK mini mud flaps!