LED Lighting Strips (Interior/Exterior)

Bed light write up!!!!

http://www.tacomaworld.com/forum/lighting/154477-diy-how-led-strip-bed-lights.html

 

well i jst did my bed lights. I put 4 in, 2 on each side. spaced it out 12" apart. And i used velcroe so that i could take them off when needed and i used a 5' connector so that i have the extra length to disattach from the velcroe and move where ever. But instead of putting the switch in the bed i put in inside the cab. And i put a fuse tap inside the main fuse box under the hood and i tapped into the horn fuse since that fuse doesnt need the ingition to be on or the key being used at all. I got say it really lights it up and might not be used every day but it will be helpful when needed. I got one pic and shows how well it lights up. If you got any question let me know. Thanks Eric, these are awsome lights!!!

 

Awesome install man!

 

subbed

 

Anyone else who has received there's get any pictures or get it installed?

 

Bump

 

im interested in running these as underbody/wheel well kits but my current target is the iceled ufo kit. what pictures can u offer of these being used as a full underbody kit to persuade me to give you my money

 

that might work pretty well for my new baja bed rack i have half way finished. only thing im worried about is the light disappearing if i cant figure out a good way to secure them.

 

I'll throw up some of my flexible strips as a temporary install for you as soon as I can

 

Maybe put molding tape on the back so they don't slide around and use those hoseclamps with the key like screws?

 

that might work but it would be hard to get them on there tight enough without damaging the lights them selves

 

Nope, because the housing of the Rigid Bars are separate from the actual electronics that you can just stop tightening before you start feeling the bar crack. But if it does, just seal it with some silicone and you should be fine.

 

I just received my lights! I got two rigid LED bars and these things are BADASS! extremely bright as you can see in the pics and those are taken in the daytime. Great product and super easy to install, it took me no more than 20 minutes to get them wired and mounted! Packaging was also very professional, these lights are a must have whether they go in the engine bay, cab or bed! they just look awesome! Thanks alot man keep making this great product i will probably be buying more in the future!
Ill post some pics of them on at night when i get a chance
Only thing is that right now they are all wired up but to turn them on i taped the positive up to the battery, i need to know how to run a switch to these if anyone can help, im a little slow when it comes to wiring

 

So...

Get one of these:

$8 Nilight GA0007 1 2Pin Way 16AWG Waterproof Wire 1.5mm Series Terminal Connector-5 Pack,2 Years Warranty

http://www.amazon.com/gp/product/B0..._m=ATVPDKIKX0DER&pf_rd_r=1PGH75YV1ES61HATM9T1

Pull out your coin holder to the fuse box behind it in the cab and put this in one of the empty slots and put a low amp fuse on the lower slot (I think) of the Add-A-Circut. Strip both ends of a wire long enough to reach from the Add-A-Circut to your switch. Slide one of the stripped ends into the blue butt connector that is included on the Add-A-Circut and crimp it. Then crimp a female end connector on to the other end of the wire and slide this on to the source pin of the switch. Then cut the end of white wire from the bars and strip that. Crimp a female end connector on to that and slide it onto the Power (ACC) pin of the switch. Find a nice metal bolt in the cab and unscrew it enough to slide the end of the black wire behind it, then tighten the bolt. Clean up the wiring (with zip ties) and you are good to go

 

Bump! Should be putting in rock lights using the flexible strips sometime next week!

 

Working on a website for our products!

 

Please Put me down for,
(3x Pair of Cool White Rigid Bars, 3x 1' Connectors, 3x 12v/Ground Connectors, 2x 12" Flexible Cool White, 1x Flex 12v/Ground Connector)
Did you get a firm price yet on this??

 

Hopefully this hasn't been asked yet but... So with the RGB box and RGB LEDs the LEDs will light up any color? So like is it possible to wire it up in a way so that every time you turn it on it lights up a random color?

 

The prices on the first post are set. I do not have the Flex 12v/Ground Connectors due to to difficulties with my supplier. You can just cut off one of the ends and connect the wires from the Flexible strips to the powersource and the ground. What are you going to use them for?

PM'd

I don't believe my controller can do that. It's possible, just not with my controller. I do have a controller that will allow it to scroll through different colors at various speeds as well as smoothly or flashing that isn't too expensive.

I also have another that can select any color you want through the RGB spectrum and can scroll through colors smoothly at various speeds but it gets pretty pricey and is usually used for homes. I can let you know if you are interested.