Scangauge II: Transmission Temp

I found these on TTROA or was it Toyota Nation posted as being for a Tundra, but might work for a Taco (I have not tried them yet)

Altitude Gauge (Feet)
TXD: 07E02133
RXF: 04610533
RXD: 2808
MTH: FEEE00016B08
NAM: Alt

Air to Fuel Ratio (Lambda)
TXD: 07E02144
RXF: 04614544
RXD: 2808
MTH: 006400800000
NAM: AFL

Air to Fuel Ratio (True Air to Fuel ratio)
TXD: 07E02144
RXF: 04614544
RXD: 2808
MTH: 05BE00800000
NAM: A/F

Atmospheric Pressure (PSI)
TXD: 07E02133
RXF: 04610533
RXD: 2808
MTH: 000A00450000
NAM: PSI


Anyone know what the speed offset for the stock TRD Sport tires might be?

 

I contacted ScanGauge today to check up on the Trans temp reading question to see if they had any new codes worked out. I asked about codes for an '06 Tacoma V6 and '05 4Runner V6 and they replied with:
" [FONT=&quot]Thank you for your inquiry. Currently, transmission temperature is only available for Ford, GM and some VW vehicles via the X-Gauge feature. The X-Gauge comes standard on the ScanGauge II and allows you to program extra gauges into your unit for your vehicle. Our engineers have found two codes in order for the ScanGauge II to display transmission temperature for Toyota vehicles, however they are very experimental so there is a possiblility that the codes may not work. [/FONT]
[FONT=&quot] [/FONT]
[FONT=&quot]TXD: 686AF101B4[/FONT]
[FONT=&quot]RXF: 044105B4[/FONT]
[FONT=&quot]RXD: 2010[/FONT]
[FONT=&quot]MTH: 000703E8FFD8[/FONT]
[FONT=&quot]NAM: TFT[/FONT]
[FONT=&quot] [/FONT]
[FONT=&quot]or[/FONT]
[FONT=&quot] [/FONT]
[FONT=&quot]TXD: 68 6A F1 01 B4[/FONT][FONT=&quot]
RXF: 04 41 05 B4 00 00
RXD: 28 08
MTH: 00 09 00 05 FF D8
NAME: ATF[/FONT][FONT=&quot] [/FONT][FONT=&quot][/FONT]
[FONT=&quot]Please let us know the results of the these codes for your vehicle and if you have any further questions"

Anyone try these codes and see what they get?
[/FONT]

 

Sorry, no go on my 2010. I triple checked both entries in my SGII. Neither one shows a value being returned in gauge mode.

ETA: I googled for a while and found these exact codes listed on tacomaterritory.com, claiming someone on a tundra site got them from the SGII folks. This was in August of 2009. Sorry, again. No go.

 

Ok, thanks anyway, guess they aren't looking too hard to add this to their x-gauge abilities. Would have bought one if they worked for this as well.

 

I sent a friendly reminder to the folks at SG to see where they were up with their ancient promise to support TFT readings.

 

if first gens use PWM how come my scangauge says its ISO

 

Transmission temperature for 2010+ tacos. Enjoy!

Transmission Temperature 1 (Degrees F) 2010+
TXD: 07E02182
RXF: 046105820000
RXD: 2808
MTH: 00090005FFD8
NAM: TF1

Transmission Temperature 2 (Degrees F) 2010+
TXD: 07E02182
RXF: 046105820000
RXD: 3808
MTH: 00090005FFD8
NAM: TF2
*
It’s theorized that TF1 is the pan temperature, while TF2 is the converter outlet temperature so TF2 will fluctuate much faster than TF1 will.

 

Does anyone have the SG2 codes for MAP sensor? For 2010+ tacoma

 

.
Sub'd ... want to get a S/G later.
.

 

As far as I know, when a car has a MAF, it does not have a MAP. So the tacoma does not have a MAP... so no code for it.

 

Hey everyone, I've had a scangauge in all my cars. I just picked up my 05 Taco and wanted to find out if anyone has found a code that works for TFT?

Thanks!

 

Post #27 above worked a treat for my 2013 Prerunner.

Thanks, Andrew

 

Post #27 above worked for my 2014 Sport.

Thanks, Andrew

 

for 2005 - 2009

https://www.tacomaworld.com/threads/johnsons-silver-bullet.85962/page-20#post-8801305


Transmission Fluid Temperature
TXD: 07E021D9
RXF: 032180000000
RXD: 2810
MTH: 00070065FE70
NAM: TFT
In degrees F

 

Does anybody know why my Scanguage pulled my trans temp on my 99 Prerunner but won't pull trans temp on my 99 4wd?

 

any update? I want to buy a scan gauge but SG cant confirm that it will work reading trans temps with my 2005 tacoma prerunner with 4.0
thanks

 

Works on my 05 Tacoma 4x4 w 4L.

 

yup still wont work on the pre-runner for some reason...Not sure why it only reads it on 4x4's

 

For you guys that are able to get transmission temp readings on your Scanguage. Can you check your software version. I currently have 2 guages. One is a 3.15 version and the other is a 3.17 version. Neither will read the transmission temps when in xguage mode. Website says to send unit to them for a $25 update. Want to know what software versions are working for you all. Thanks!

 

The codes for TFT worked on my 2003 Tacoma PreRunner.