1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Need pics of wiring from roof (lights on rear)

Discussion in '2nd Gen. Tacomas (2005-2015)' started by Icepuck72, May 12, 2014.

  1. May 12, 2014 at 5:10 AM
    #1
    Icepuck72

    Icepuck72 [OP] Well-Known Member

    Joined:
    Jul 9, 2011
    Member:
    #59563
    Messages:
    1,809
    Gender:
    Male
    First Name:
    Mark
    Richmond, VA
    Vehicle:
    2006 DC TRD
    OME 885's, Dakars, TRD Trail Edition Wheels, 285x75x16 Goodyear Duratracs, Magnaflow 12256 muffler, Fog Light mod, 2 Baby seats
    I've searched, and have seen a couple of pics, but not clear. If you can find one or have done this, can you snap a few?

    Lights will be mounted on the REAR of my YAKIMA BAR. Not sure where to run the wires coming from the rear. Should I run the wires along side the roof rack down the pillar up front?
     
  2. May 12, 2014 at 10:19 AM
    #2
    Icepuck72

    Icepuck72 [OP] Well-Known Member

    Joined:
    Jul 9, 2011
    Member:
    #59563
    Messages:
    1,809
    Gender:
    Male
    First Name:
    Mark
    Richmond, VA
    Vehicle:
    2006 DC TRD
    OME 885's, Dakars, TRD Trail Edition Wheels, 285x75x16 Goodyear Duratracs, Magnaflow 12256 muffler, Fog Light mod, 2 Baby seats
    no one?
     
  3. May 13, 2014 at 6:07 AM
    #3
    boomer6

    boomer6 Well-Known Member

    Joined:
    Apr 22, 2011
    Member:
    #55337
    Messages:
    508
    Gender:
    Male
    First Name:
    John
    TN
    Vehicle:
    Tacoma TRD Offroad
    disabled DRLs disabled seat belt chime disabled the key in the ignition with door open buzzer Installed Illuminated 4wd switch circuit board Marker lights Flashing with turn signals Toggle switch ABS Disable Fog Lights on AnyTime Mod Changed to Yellow bulbs in the Fog Lights Converted interior lights to leds Installed oem roof rack Installed Firestone Ride Rite Air Bags and Daystar Cradles for the air bags Added oil catch can Relentless Tailgate Protector installed
    I ran my wires in a wire loom down back of cab by the third brake light, down between cab and bed , then uder cab.I have a double cab, drilled a hole thru a large rubber plug located under rear seat. ran wires under carpet.zip tied as i went. silicone the rubber after putting wire loom thur it. Been almost three years no problems or leaks.Put my switches in the cubby hole in front of shift lever ...bottom of dash. Some where on I think it was OZ posted a link to an item that go thru the roof , thinks it waterproof...try doing a search. hopes this gives you a starting point.
     
  4. May 13, 2014 at 6:20 AM
    #4
    boomer6

    boomer6 Well-Known Member

    Joined:
    Apr 22, 2011
    Member:
    #55337
    Messages:
    508
    Gender:
    Male
    First Name:
    John
    TN
    Vehicle:
    Tacoma TRD Offroad
    disabled DRLs disabled seat belt chime disabled the key in the ignition with door open buzzer Installed Illuminated 4wd switch circuit board Marker lights Flashing with turn signals Toggle switch ABS Disable Fog Lights on AnyTime Mod Changed to Yellow bulbs in the Fog Lights Converted interior lights to leds Installed oem roof rack Installed Firestone Ride Rite Air Bags and Daystar Cradles for the air bags Added oil catch can Relentless Tailgate Protector installed
    If you go to my gallery there are two pics ( Not that great) that show the wire loom by third brake light. There are 6 wires inside of the wire loom.Four are for radios.
     

Products Discussed in

To Top