1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Clutch Obnoxious Squeak Fix

Discussion in '4 Cylinder' started by dcpatrick, Dec 2, 2014.

  1. Dec 2, 2014 at 12:25 AM
    #1
    dcpatrick

    dcpatrick [OP] New Member

    Joined:
    Dec 2, 2014
    Member:
    #143471
    Messages:
    1
    Gender:
    Male
    Vehicle:
    2011 base model 4 banger
    Rear sway bar
    After hours of tinkering, I finally found a way to fix this terrible noise I used to get while pressing my clutch in. I've compiled a PDF, and I hope it will help those who were as clueless as I was when it came to attempting to fix it.
     

    Attached Files:

  2. Dec 2, 2014 at 12:45 AM
    #2
    QMEDJoe

    QMEDJoe Proverbs 3:5-6

    Joined:
    Nov 4, 2014
    Member:
    #141714
    Messages:
    2,391
    Gender:
    Male
    First Name:
    Joe
    Columbus Grove, Ohio
    Vehicle:
    2003 Tacoma, V6, 5 speed, 4x4.
    Fox 2.0 Coilovers in the front and Fox 2.0’s in the rear, Total Chaos UCA’s, Al-lpro expo leafs, K&N cold air intake, TRD headers,Magnaflow catback exhaust,URD short throw shifter, switched out my 60/40 bench seat for some Tacoma Limited seats, Replaced the vinyl shift boot for a leather one, completely soundproofed the cab w/ Frost King. Replaced stock radio with a Pioneer AVH series head unit. Focal component system w/a 10" sub powered by 2 Alpine amps. Weathertech floor mats. Line-X'd the bed. SCS Ray 10’s, Installed an A.R.E. MX series camper shell. All-Pro Apex front bumper w/ All-Pro skid plates all the way back to the Trans. Low Range fuel skid plate.
    Yes, I have the same issue. I haven't clicked on the PDF but there is a thread on here explaining in detail on how to fix it. Kinda tricky if you don't have a bench vise. The bushing is cheap plastic. Some guy on here used brass and it worked better.
     
  3. Dec 2, 2014 at 8:49 AM
    #3
    tooter

    tooter play every day

    Joined:
    Apr 13, 2013
    Member:
    #102021
    Messages:
    2,456
    Gender:
    Male
    First Name:
    Greg
    Los Angeles
    Vehicle:
    2012, std cab, 5 lug, 2.7, 5 speed
    Built for maximum low end torque, tooter II.VII intake manifold spacer, LCE long tube header, Injen long tube intake, 2,900 rpm torque peak.
    Welcome to TW, Patrick, :wave:

    My clutch doesn't squeak, but if it ever does thanks to you I'll know what to do. :)

    Greg
     
  4. Dec 2, 2014 at 8:52 AM
    #4
    adamr94

    adamr94 Well-Known Member

    Joined:
    May 12, 2014
    Member:
    #129691
    Messages:
    244
    Gender:
    Male
    First Name:
    Adam
    NC
    Vehicle:
    06 Regular Cab 4x4
    Thanks! I'll have to try this out when I get some time.
     

Products Discussed in

To Top