AZ 2A classifieds without the politics

Anyone happen to have a barrel nut wrench for Sons of Liberty barrel nuts?

 

Im pretty sure I do, I bought one of their broadsword uppers and rails and then never did anything with it.

 

I want it to disassemble a M89 300 blackout upper and then won’t need it again. Could I borrow it from you if you have one?

 

Yeah I've got it. You want me to disassemble the upper for you? I've got all the jigs and fixtures to do it without putting any stress on the barrel extension indexing pin that can shear off if there is too much gronk applied without properly supporting the upper.

For AZTW members it's a free service.

 

If you ever Assemble an AR Upper, I highly recommend "shiming the barrel."
Lots of guys know how this is done and have the equipment to do it. @Nitori - I'll bet you have done this.

Essentially where my upper receives the barrel wasn't milled perfectly cylindrical - they are all a wee bit off. Wider in the back than in the front - was allowing a tiny bit of barrel wobble. Guy on Arizona Gun Owners was able to check the run-out on it and then shimmed it what what looked like metal tape that he super glued in there. Two shims thick at the back and one up front. Then we put them back together (took some grunting and cussing) super tight! Torqued to spec. AR got more consistent by a magnitude of 10x. Was shooting Minute of Comrade, now shooting 4" groups at 100 yards and that has way more to do with my eyes than the gun. At 50 yards they almost all touch.

So many AR parts are quickly mass produced these days that a not everything is as good as Mil-Spec and we know how good that isn't to begin with.

 

Yes sir, all my barrels on self-built uppers are shimmed. I do occasionally buy Centurion arms or BCM thermal fit uppers. They specifically undersize the barrel extension and you gotta heat it up with a torch or a heat gun and then shove it on there quick before the aluminum sheds the heat.
My M16A2 clone shoots like a dream & I used the trick- I was able to double tap steel targets at 200 yards.

The original stoner design was supposed to be a clearance fit for mass production, but it was a trick apparently discovered during marksmanship competitions.

I've never tried loctite green or gluing in the shims- there's not really a good reason to aside from ease of assembly, but you pay it back in ease of disassembly. I have a 1" wood dowel that I sanded to about .998" that goes inside the receiver and taps out the barrel.

 

Anyone looking for an M7 bayonet? $50?

 

Anyone unloading a Glock 22?

 

GEEZ! Smokin good deal!
Just looked them up and they are going for $150 to $200. Some chewed up and used ones are $80.

 

Where? I'll post over there, haha.

 

FleaBay

 

Of course, ha.

 

Getting rid of my 300 blk for real this time.

$300 OBO for the lot of it, 500+ total rounds. thats crackhead pricing but I have some other 2A stuff Im looking at swapping into.

200 rounds Ammo inc 150gr supers
50 rounds Remington 220 subs
100 rounds federal 220 subs
50 rounds freedom munitions ??gr supers
100 rounds factory ammo from Rainier arms and... somewhere else mixed. Supers.
1 300 blackout PMAG (included) with what looks like 220 hollow points
And then some loose rounds.

ALL FACTORY AMMO I dont do Bubbas pissin hot reloads

 

Located in Prescott, but willing to drive for reasonable offer

Arsenal AK SAM7 SF + Accessories $2,200
Bulgarian made, Arsenal SAM7SF. Milled receiver w/ factory ALG trigger and thumb safety. Includes oem stock, cleaning kit, MI handguard, MI pic stock tube, jmac stock adapter, AK master mount. Less than 1k rounds down the pipe. More pics available on request.



P365 XL w/ EPS carry setup - $1,200
P365 XL, wilson combat grip module, EPS carry, 2 17rd mags, 2 12rd mags, 1 10rd mag, Trex arms sidecar holster.