Behind the rear seat storage - My solution

Dagwood

 

I have pricing!

This is for 1/8" aluminum and a minimum order of 5 for each size. Does NOT include shipping.

Small (15"): $180

Medium (30"): $235

Large (48.75"): $350

I will start a group buy thread and post a link here, either later or tomorrow.

 

Possible sub box choices

http://www.supercrewsound.com/product306.html

http://www.supercrewsound.com/05tacomadblsingle.html

http://shop.*********.com/Tacoma-Subwoofer-Enclosure-10-Loaded-DCT-TACO-SUB10-1L.htm

There have to be others too.

 

What if you ordered 25+ would the price go down?

I have a mr marv box. I would need to do a full length and cut around my sub box.

How would this do with a linex coating?

Would steel be any cheaper?

 

Im still curious on a price and shipping cost.

What other clean storage idea have people come up with?

 

Price is a couple posts up

 

I apologize for sounding like a newb but if you have the JBL with the factory sub you can only fit the small piece without major modifications?

 

OP, what size is yours?

Is it the 48.75" that covers the whole back cabin wall behind the seat?

if so, ill take it!

 

i think it would be clearer to state the sizes a in full wall, half wall passenger, half wall driver, full wall lower half, full wall upper half, or a quarter size of each quadrant... whatever pieces work

 

You can completely remove the driver side cubby with no complications to the JBL setup.

 

My in laws were in town for a few days and my time was needed far more than I thought. Here is the buy thread:

http://www.tacomaworld.com/forum/2n...anel-group-buy-second-gen-dc.html#post8489305

 

I had a friend come through for way better pricing, like half as much. I will update the buy thread.

 

So the 15" would replace the driver's side storage bin?

 

i think so, it would be nice to be able to mount some stuff for quick access

 

Nice. I have Mr. Marv's sub enclosure taking up the whole passenger side.

 

I am definitely interested

 

These look great and very usable. I would be interested in the large/full size/48" shipped to 66043.

Q1. By removing the plastic behind the seat how does that effect the sound in the truck cab. Louder?

Q2. How much drilling to mount? Tried finding it in thread.

Q3. Are these being sold yet?

Thanks. Also on the seat covers that have the molle pouches on the back, I found that at least a couple of them were not a usable size. Also because they are on the back of the seat they stop you from putting your back seats down. They also get in the way of your passengers. Just my experience with the back of the seat molle setups.

 

very good looking rack

 

Sub'd for awesome molle mod

 

Wasn't planning on taking out the plastic storage bins until I saw that you could actually fit a hi-lift jack back there. Couldn't pass up tearing out the storage bins after I saw that. Picture below of what I did. Total cost is probably about $15.

Added some vinyl floor runner to protect the metal back and bottom with the storage bins removed. Screwed in 2 tool pouches. Would have done more, but car seat prevents me from easily folding down the rear driver's seat.

I have a couple courts of oil, bailing wire, lots of hand tools, hi lift, 12 feet of heavy chain, 2 snatch blocks, 30 foot tow strap, 10 foot tow strap, tree saver strap, a bunch of work gloves, tire deflator, tire repair tools, and probably a few other things I can't think of. I keep a few other things like jumper cables underneath the seat. Some larger tools and ratchets get put behind the driver seat in a good sized tool bag.

Looking to get rid of my plastic storage bins if anybody wants to make a low offer to pick them up in Southern Wisconsin.