Custom Overhead Console Switch Panels - Updated 6/26/2017 Now availalbe!

The Pirate · Nov 30, 2020

helix66 said: ↑

Will the overheads work with crawl control on an off road?

I lost track, the 2Lo is plug n play?
Click to expand...

2Lo is plug and play and awesome. But I have a manual transmission, thus no crawl control.

https://www.tacomaworld.com/threads...-2wd-low-range-for-the-3rd-gen-tacoma.614743/

'16goingon'17 · Oct 5, 2021

I haven't seen anyone do this so I am wondering if I can just replace the Passenger Side Overhead Switch Panel with this from @tacitos instead of replacing all three panels? All I need is a spot for the 2Lo switch.

Grossomotto · Oct 5, 2021

You can, I did the swap on mine. Although, I think there's a cheaper one on Shapeways or Etsy.

Edit, after searching only see your link

'16goingon'17 said: ↑

I haven't seen anyone do this so I am wondering if I can just replace the Passenger Side Overhead Switch Panel with this from @tacitos instead of replacing all three panels? All I need is a spot for the 2Lo switch.
Click to expand...

URBAN_COWBOY_TACO · Dec 26, 2023

Is there an option to purchase the CAD file?

RippNU1 · May 30, 2025

tacitos[OP] initial post: ↑

I started working on this last month and finally have something worth showing.

@KTJO 4x4 nudged me to do it, and @Jgchfd was kind enough to lend me a spare console for development. Thanks to both of them for helping me make this happen.

The challenge was to add more switches in natural places, the overhead console seems to be under used at times depending on the trim level of truck that you own. So naturally some of us want to make better use of that space and add switches for whatever accessories we want.

The issue is that Toyota does not sell the switch panels, instead you have to purchase a complete console to get the switch panel your looking for. The other issue is that there is no switch panel for the passenger side of the console. This is only used for trucks with sunroof's.

So I set off to reverse engineer the existing panels to accommodate additional switches. While I was in there, I decided to design a complete switch panel that installs within the Sunglasses holder of the console. All together we are looking at a total of (9) small OEM switches in the overhead console with minor modifications.

Now available for purchase through Shapeways

Driverside Switch

Center Switch Panel

Passenger side Switch

Installation Instructions

The hardest part here is going to be adding the passenger side switch (typically reserved for the sunroof). Because of the original design of the console, one will have to cut into the plastic frame behind the console to allow clearance of the switch. Not only that, its impossible to remove the dummy plate without taking the console completely apart.

For those of you wondering about the center console switch panel I've been talking about making for a long time, its still in the works. I decided to use the smaller format OEM switch, which requires me to make some modifications to the design. The small switch is the way to go.

For the overhead console, I have the sizing just about done, just need to add the switch ports and print the prototypes. I'm going to be sending a sample set to @KTJO 4x4 to test out. My overhead console is pretty much all used up from the factory.

The sunglasses holder switch panel is still in the sizing stage. But here you can get an Idea of what to expect. Once installed, the switches can be tucked away by closing the sunglasses holder tray. Unfortunately due to crawl control, I wont be able to use this one in my truck.

I'll be posting updates to this thread as I progress.

Update: 2/6/2017

I've dialed the switch port on one of the panels. Next I'll be transferring it over to the center & passenger side panels.

Also test fitting for the Sunglasses holder switch panel is looking promising. The pic below shows only the center section, but the final design will fill the whole panel.

Below is what you could expect to do to fit and wire additional switches.

I've highlighted the areas of interest.

Red Box: These are the plastic tabs that hold the back and front panels of the console together. These must be snapped or cut off with a dremel. Once complete, you will be able to modify the console to install the passenger side switch (sunroof) or add (5) switches. Once complete, high strength Glue like Goop can be used in these spots to secure front and back panels together.

Orange box: will have to be cut out to allow for clearance of the passenger side switch (sunroof)

Green & Blue Box: Cutting these out will allow you to fit the (5) switch configuration panel.

Blue Circle: Is where I would thread the wiring loom of the switch panel housed in the sunglasses holder.

Update: 2/7/2017

The main panel is almost done, just have to print and do final fitment tests.

Update: 2/13/2017

I took apart the overhead console to finally get a better look inside. Discovered the Sunroof switch port is in fact laid out differently from the rest. So I have to revise the design of the switch panel for the passenger side (sunroof).

Below are some pics of the switch panels mocked up. I will post some closeups of inside the console tonight.

Update: 4/2/2017

Finished in black ABS, will be printing some pieces for @KTJO 4x4 to evaluate this week. Also Putting a list together for those interested in buying.

Update: 5/15/2017

Here is a sample of the switch panels with populated with switches. Will be available for purchase soon.

Update: 6/26/2017

Thank you all for your patience, the moment has arrived.

Click Here for Installation Instructions

Please provide any feedback on the instructions.

Console switches now available for purchase on Shapeways. Links at the top of this thread.

Click to expand...

Im probably a little late in doing this but I haven’t had my Taco long. The links to the different sized overhead pieces are broken links now. But all I am looking for is the two switch panel that goes in the middle of the overhead console. Do you have any of these left for sale?? And as for the place that made some in the past the link just takes you to a home page for the place. I would t kno what kinda of info they would need to even print one for me. Can I get a little assist here please…..? Thanks guys…

Log in or Sign up

Welcome to Tacoma World!

Custom Overhead Console Switch Panels - Updated 6/26/2017 Now availalbe!

#261
The Pirate Takoyaki Takoma

#262
'16goingon'17 Well-Known Member

#263
Grossomotto Complete 3rd Member

#264
URBAN_COWBOY_TACO Member

#265
RippNU1 I keep telling the voices in my head…..”NO!!!”

Products Discussed in

Log in or Sign up

Useful Searches

Welcome to Tacoma World!

Custom Overhead Console Switch Panels - Updated 6/26/2017 Now availalbe!

#261 The Pirate Takoyaki Takoma

#262 '16goingon'17 Well-Known Member

#263 Grossomotto Complete 3rd Member

#264 URBAN_COWBOY_TACO Member

#265 RippNU1 I keep telling the voices in my head…..”NO!!!”

Products Discussed in Entire Site Forum: 3rd Gen. Tacomas (2016-2023) Thread: Custom Overhead Console Switch Panels - Updated 6/26/2017 Now availalbe!

#261
The Pirate Takoyaki Takoma

#262
'16goingon'17 Well-Known Member

#263
Grossomotto Complete 3rd Member

#264
URBAN_COWBOY_TACO Member

#265
RippNU1 I keep telling the voices in my head…..”NO!!!”

Products Discussed in