1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site
  1. May 10, 2012 at 8:45 PM
    #1
    Toyotacerttech

    Toyotacerttech [OP] Well-Known Member

    Joined:
    Jun 27, 2011
    Member:
    #58963
    Messages:
    162
    Gender:
    Male
    First Name:
    Michael
    Texas
    Vehicle:
    2011 double cab 4x4 TRD
    I am selling an engine ecu reflashed for the trd supercharger from a 2008 Tacoma prerunner it has about 100 miles on it, and it should have the old calibration before the 90l recall but I don't remember but I can check. Calibration ID 3ywg0300 should fit 2005-2009 2 & 4 wd with a/t part number 89661-04c71

    400.00 shipped o.b.oImageUploadedByTapatalk1336707938.665878.jpg
     
  2. May 11, 2012 at 12:43 AM
    #2
    babyboi2284

    babyboi2284 Well-Known Member

    Joined:
    Dec 31, 2010
    Member:
    #48525
    Messages:
    567
    Gender:
    Male
    First Name:
    Brian
    Lockport, Louisiana
    Vehicle:
    09 Barcelona Red X-Runner
    LS 6k projectors w/ white halos, 6k fogs, T-Rex Angry Lids, NST SSK, Coupe Shift Knob, BHLM, LFM, DLM, FLM, JL 500/1 amp, JL 10"w6v2, subX wanna be made by me, Magnaflow muffler, 5% tint, k&n drop in filter, Craven Speed Stubby, map light mod
    This will not be a direct "plug in and go" even if you have a supercharger. You will have to bring it to a dealer for them to flash it to the new truck and from what I read that can't be done.
     
  3. May 11, 2012 at 2:11 AM
    #3
    Toyotacerttech

    Toyotacerttech [OP] Well-Known Member

    Joined:
    Jun 27, 2011
    Member:
    #58963
    Messages:
    162
    Gender:
    Male
    First Name:
    Michael
    Texas
    Vehicle:
    2011 double cab 4x4 TRD
    It can be done just need to install it and and and jump pins tc and e1 and leave ignition on run position for 30 mins so it can program to the mobilizer ecu
     
  4. May 11, 2012 at 4:10 AM
    #4
    babyboi2284

    babyboi2284 Well-Known Member

    Joined:
    Dec 31, 2010
    Member:
    #48525
    Messages:
    567
    Gender:
    Male
    First Name:
    Brian
    Lockport, Louisiana
    Vehicle:
    09 Barcelona Red X-Runner
    LS 6k projectors w/ white halos, 6k fogs, T-Rex Angry Lids, NST SSK, Coupe Shift Knob, BHLM, LFM, DLM, FLM, JL 500/1 amp, JL 10"w6v2, subX wanna be made by me, Magnaflow muffler, 5% tint, k&n drop in filter, Craven Speed Stubby, map light mod
    I'm sorry for cluttering up your thread but what does jumping the pins do?
     
  5. May 11, 2012 at 11:54 AM
    #5
    Toyotacerttech

    Toyotacerttech [OP] Well-Known Member

    Joined:
    Jun 27, 2011
    Member:
    #58963
    Messages:
    162
    Gender:
    Male
    First Name:
    Michael
    Texas
    Vehicle:
    2011 double cab 4x4 TRD
    That's ok it registers the ECM to the immobilizer ecu so that the ECM communication ID matches. Also I messed up its terminals TC and CG. Also the vin needs to be reprogrammed with a scan tool if not you will get a p0630 but it will still start.
     
  6. May 13, 2012 at 3:58 PM
    #6
    Toyotacerttech

    Toyotacerttech [OP] Well-Known Member

    Joined:
    Jun 27, 2011
    Member:
    #58963
    Messages:
    162
    Gender:
    Male
    First Name:
    Michael
    Texas
    Vehicle:
    2011 double cab 4x4 TRD
  7. May 16, 2012 at 8:37 PM
    #7
    Toyotacerttech

    Toyotacerttech [OP] Well-Known Member

    Joined:
    Jun 27, 2011
    Member:
    #58963
    Messages:
    162
    Gender:
    Male
    First Name:
    Michael
    Texas
    Vehicle:
    2011 double cab 4x4 TRD
    Bump 300 shipped
     
To Top