Fitting 35’s with minimal trimming NOW ADDING LONG TRAVEL AND 934 CV’s

I'm going to add a little to this entire debacle, even though I feel that @81Trekker addressed the question pretty well.

To some extent, I think that the people who have been in this thread since the beginning are tired of the redundant questions that keep popping up which is what @Airdog was referencing in his post. JD Fab is a reputable race shop that specializes in building legit race vehicles. Their primary business is not to cater to the redundancy of the Tacoma owner who wants the best product for the least amount of money and effort.

To address @65skyturbo statement about the stock length LCAs, the consensus is you're wrong. I'm not saying that from the standpoint of being a dick, I'm saying that when you look at the overall demand in the market for the existing comparable products from other manufactures, there are very few sold. So it may be appealing to you because you don't have the ability/willingness to put in the fab work or labor for the install but there wouldn't be enough time to justify Harry investing R&D time into the product.

This same question is asked in some variety every couple of pages with the same answer. Along with 3rd gen owners asking about the oil filter relocation for the slide rack. Some of the seasoned members in this thread almost expect you to read before you post like they did but we have to keep in mind that there are 300+ pages of this thread now. Most of which is BS.

That said, we also interact over the internet and you learn everyone's quirks to a point. If you did read the thread you'd know that @Airdog is a dick and @kasnerd has one of the badest trucks out there but is afraid to drive it (joking) but also likes to be an internet expert based off his experience which vastly differs from others. New thread members just haven't caught on to any of it yet.

Regardless, my pointless rant is over. Who's going to Fiesta next weekend so we can BS in person? I'll be making an appearance for a few hours. Might not bring the truck though. It's kind of embarrassing compared some of these new rigs. lol

https://www.tacomaworld.com/threads...bq-and-bs-meet-up.721954/page-8#post-25841537

 

Well you'd get your hands on them then. Plus get to see the install process in person.

 

Wish my truck was on the ground or else I would go. I’ll have to convince a whole family trip with the accord to make it haha.

 

Day rentals at Enterprise are cheap. Get a nice Crossover that gets good MPG.

 

Can they come PCd???

 

Hmmm I am running out to cali next weekend. But taking the race support Elantra and heading a little north of there. Should be a fun meet and greet though

 

you misspelled POR15

 

I have a few extra trucks you can borrow

 

Just a few? This guy could start Enterprise Rent-a-Badass service from the inventory at his house alone. lol I wanna borrow the loaner, mishell!

 

No you see I'm getting those and was going to pay extra and have yours PC lime green and hot pink candy stripped.

I have enough experience with POR15 no thanks. I'll just spray bomb them or take them to a local guy for some PC. Harry's PCer is just cheap.

 

po-tay-toe, pah-tah-to. PC is good choice but media blast it first. made acetone only prep mistake before.

 

I’ll swing by and pick one up then! I still want to feel the steering pump difference too.

 

dinner and drinks before getting to feel around.

 

Any recommendations for tranny cooler? I saw the one that @81Trekker installed recently, but I don't know if I can give up the space in the back. Swapping tranny's right now so want to make sure I don't explode this one

 

Sparkling Campari

 

cooling a tranny? you want shade for that.

 

I used “Long Tru-Cool LPD Transmission Oil Cooler 4590” some generic name for the same part as one of the bigger known brands. It helped a ton when I went to 315s on stock gears.

 

For shit I actually care to coat right I clean with acetone scuff and then final clean again. Then good coating of whatever choice. Has worked pretty well. Many ways to skin that cat.

 

Custom mini washer fluid container so @kasnerd can wash all the roost everyone will be throwing at him