FS: Aluminum Seat Spacers, Risers, Jackers For Seat Mod, Xmas Sale

Glad I just found this thread. Cant wait to try this out. I love my truck...except for the sunk in feeling and bad sight lines. Thanks for doing this Dennis! Order for 2 on the way thru paypal.

 

I'm also 6'2"
Put these on, and love the difference . My leg is no longer falling asleep when I drive to work.

 

Received the set, thanks Dennis!

Quick question: Is there a write-up for the seat mod / installing the hardware?

 

I'm not mechanically inclined and I just grabbed hold of the plastic cover over each seat foot bracket and pulled those off and set aside then removed the factory bolts. Lifted the rear of the seat so I could get a spacer under each back seat bracket foot. Then I decided I would like a nice heavy washer under the bolt head so I put a washer on each bolt/hardware and stuck the bolt through the seat bracket foot and spacer then held my mouth in various positions until I got the bolt started in each of the 2 holes. Tightened each bolt pretty tight then snapped the plastic cover over the each seat bracket. All done.

 

Received these the other day and installed faster than finishing a beer while it was raining. With the 1" spacers, these individual blocks are a much better solution than a few thick washers. At 5'10", seat angle and view have improved to more of my liking.

Thanks Dennis; fast service and a quick turn-around on product. Much appreciated!

 

Installed on both front seats, love it! Thanks again Dennis, and keep up the great work!!
Mod on!

 

Where's the paypal link? I wanna try this out

 

Received yesterday and installed. Could immediately tell the good difference in comfort. Immediately knew my passenger needed this mod too. Ordering another set today! This time I will get the .75 inch. I’m 6’2” and I barely fit in this truck with a 1” so figure I will move the 1” over to the passenger side.

 

Cooters@tampabay.rr.com

 

Thank you everybody. My paypal link is cooters@tampabay.rr.com I have enough materials ( I think ) to carry me to Feb. after that starting Feb. 1st I have to raise the price of spacers from $7.50 each to $10 each. My material cost went up , even my bolt cost went up. Not sure why but I will keep them as low as I can. Thanks again everyone.

 

Starting Feb. 1st the price will be $10 each and not the $7.50 materials have gone up. I think I have enough in stock till then. So your cost after Feb. 1st for one seat will be $27 without bolts or $32 with bolts and that includes $7 shipping. For both seats $47 without bolts or $57 with bolts. Sorry but not making much as it is and have to go with the flow. Thank you

 

Just put my order in last night. Thank you sir for putting your time in to make these.

 

You are very welcome. Hope your back end appreciates it.

 

Got mine already! Came home exhausted from work but had to install right away. Piece of cake....10 minutes. First time I have ever really felt the lumbar support in the drivers seat. The difference is unbelievable for the small amount you raise the seat. I didnt think it could be that noticeable but so many on here said it was. They were all right. THANK YOU Dennis for the quick shipment of my order. I love them. Will do the passenger side this weekend.
Guys and ladies....jump on this while its available. GREAT mod!

 

Thank you for sharing bro!

 

Money sent for 2 sets

 

I went and checked the thread and there are Older Tacoma owners. You would think Toyota would catch onto this problem and add a height adjuster.
My wife's 2010 Corrla has adjustment on hers, you pump the handle to go up or down, it does not need to be electric. I am sure they know about this?

 

Just sent payment for 2 sets of spacers. Thanks for your design and execution with this!

 

PayPal sent for 1 set for driver's seat....Thanks!

 

Funds sent for 1' driver and passenger...thanks!