1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

How to?

Discussion in '2nd Gen. Builds' started by regcabtaco, Aug 27, 2010.

  1. Aug 27, 2010 at 10:32 PM
    #1
    regcabtaco

    regcabtaco [OP] Well-Known Member

    Joined:
    Oct 3, 2009
    Member:
    #23738
    Messages:
    60
    Gender:
    Male
    idaho
    Vehicle:
    05 tacoma sr5
    I was wondering how you remove the muffler and exhaust from the rubber anti-vibration holders keeping them both in place?
     
  2. Aug 27, 2010 at 10:33 PM
    #2
    stmpjmpr

    stmpjmpr Well-Known Member

    Joined:
    Jun 2, 2010
    Member:
    #38246
    Messages:
    1,967
    Gender:
    Male
    First Name:
    Jimmy
    So Orange County, Ca
    Vehicle:
    2014 Tacoma Sport MGM 4X4
    WD-40..should slide out. make take some elbow grease
     
  3. Aug 27, 2010 at 10:48 PM
    #3
    regcabtaco

    regcabtaco [OP] Well-Known Member

    Joined:
    Oct 3, 2009
    Member:
    #23738
    Messages:
    60
    Gender:
    Male
    idaho
    Vehicle:
    05 tacoma sr5
    Thanks, I appreciate the advice.
     
  4. Aug 27, 2010 at 10:54 PM
    #4
    STravis

    STravis Well-Known Member

    Joined:
    Feb 2, 2010
    Member:
    #30597
    Messages:
    721
    Gender:
    Male
    First Name:
    Travis
    Ruidoso, New Mexico
    Vehicle:
    2012 TRD Offroad
    Haha and don't do it when its cold outside. It makes it very difficult.
     
  5. Aug 27, 2010 at 11:28 PM
    #5
    regcabtaco

    regcabtaco [OP] Well-Known Member

    Joined:
    Oct 3, 2009
    Member:
    #23738
    Messages:
    60
    Gender:
    Male
    idaho
    Vehicle:
    05 tacoma sr5
  6. Aug 27, 2010 at 11:35 PM
    #6
    CopDoctor

    CopDoctor Well-Known Member

    Joined:
    Feb 1, 2010
    Member:
    #30474
    Messages:
    1,874
    Gender:
    Male
    First Name:
    Matt
    Colorado Springs, CO
    Vehicle:
    08 335i
    BMS Intake, JB4 chip, Plastidip everywhere
    bump, why? did it not work?
     
  7. Aug 28, 2010 at 7:16 AM
    #7
    chris4x4

    chris4x4 With sufficient thrust, pigs fly just fine. Thor

    Joined:
    May 8, 2008
    Member:
    #6497
    Messages:
    103,833
    Gender:
    Male
    First Name:
    FlimFlubberJAM
    Tenoe, AZ
    Vehicle:
    2013 Rubicon Unlimited,
    4.10 gears, sliders, and lots of buttons.
    This. Use a pair of pliers to work the rubber off the hangers.
     
To Top