RTMR wiring to ARB locker and compressor

ramonortiz55 · May 15, 2017

ajsabra said: ↑

So how did this work out in the long run using a relay from the RTMR? did you use 10 gauge TXL wire for it or just 12 Gauge GXL wire... Im about to do the same thing, I just dont want a crap load of accessory wires/relays under my hood.
Click to expand...

10 gauge. works perfectly

ajsabra · May 15, 2017

Awesome thanks, I'm pulling the trigger on building my rtmr. Gonna cost me about 300, but I get to keep new tools

Base Camp · Jul 5, 2017

Glad I found this. Thanks guys. Planning on wiring up my compressor for rear locker to my "skygear" box soon and this was very helpful.

Naveronski · Jun 12, 2020

Bumping this.

How has it been for you?

I want to incorporate my dual compressor into my box, if possible.

ramonortiz55 · Jun 12, 2020

Naveronski said: ↑

Bumping this.

How has it been for you?

I want to incorporate my dual compressor into my box, if possible.
Click to expand...

never had an issue

w8tdstrgecube · Feb 22, 2021

ramonortiz55[OP] initial post: ↑

So I have one of @skygear RTMR boxes installed in my 3rd gen 4runner:

@skygear did us the favor of putting together the wiring of the box, relays, and switchbacks to where all I have to do is splice the power of my accesory to the power lead from the box and install my OTTRATW switch:

As you can see, I already have the OTTRATW switch and no longer need the supplied switches from ARB nor their relay and wiring harness since all of that is covered with the RTMR.

So my question is:

Has anyone been able to wire their ARB compressor and locker to the RTMR?

If so, what wiring did you run where? LOL

I see three things in the below schematic that I have to wire:

Pressure switch, compressor and solenoids.

ARB wiring schematic:

I figured the power motor for the compressor would be me just connecting the power lead from the circuit the compressor is going to be at.

But I have the pressure switch and solenoids..does anyone have any ideas on how I could tackle the remaining wiring??

I am either someone has done this by now, or this will need to happen soon on someone's install..
Click to expand...

Not sure if you figured this out yet, but I did most of what you're referencing and wrote it up here. Assumes your RTMR is wired the same way as mine (running relays upside down). I am not running lockers though.

Log in or Sign up

Welcome to Tacoma World!

RTMR wiring to ARB locker and compressor

#21
ramonortiz55 [OP] Not A Well-Known Member

#22
ajsabra Fully locked 3rd gen

#23
Base Camp Instagram: @willismtc

#24
Naveronski Well-Known Member

#25
ramonortiz55 [OP] Not A Well-Known Member

#26
w8tdstrgecube Well-Known Member

Products Discussed in

Log in or Sign up

Useful Searches

Welcome to Tacoma World!

RTMR wiring to ARB locker and compressor

#21 ramonortiz55 [OP] Not A Well-Known Member

#22 ajsabra Fully locked 3rd gen

#23 Base Camp Instagram: @willismtc

#24 Naveronski Well-Known Member

#25 ramonortiz55 [OP] Not A Well-Known Member

#26 w8tdstrgecube Well-Known Member

Products Discussed in Entire Site Forum: Technical Chat

#21
ramonortiz55 [OP] Not A Well-Known Member

#22
ajsabra Fully locked 3rd gen

#23
Base Camp Instagram: @willismtc

#24
Naveronski Well-Known Member

#25
ramonortiz55 [OP] Not A Well-Known Member

#26
w8tdstrgecube Well-Known Member

Products Discussed in