1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

SOLD!!!! (4) Spidertrax 1.25" Wheel Spacers - $150 - ABQ, NM

Discussion in '1st Gen Tacoma Parts Marketplace (1995-2004)' started by BigFishAllDay, Jan 21, 2017.

Thread Status:
Not open for further replies.
  1. Jan 21, 2017 at 6:19 PM
    #1
    BigFishAllDay

    BigFishAllDay [OP] And then?

    Joined:
    Oct 3, 2012
    Member:
    #88250
    Messages:
    897
    Gender:
    Male
    First Name:
    Nick
    ABQ, NM, USA
    Vehicle:
    I have too many Toyotas...
    Everything... and a bag of Cheetos.
    SOLD!!!!!

    I've got a set of four Spidertrax 1.25" wheel spacers that I recently purchased from another forum member on T4R.org. These are the blue anodized model #WHS007, hub centric and lug centric.

    All four spacers are in good shape, with a few dings from install/removal by the prior owner. The threads on both the studs/lugs are in good shape. Mounting faces are flat and true on both sides of all four, although one of the spacers did have some dings (two) on the edge of the mounting face that I had to gently massage flat with a hammer. The previous owner reported only 4,000 miles of use on these.

    I took my time cleaning them up for install, and used a wire brush to clean all the studs and lugs, ensuring that the lugs could all be threaded start to finish by hand. I also wire brushed the mounting faces to remove dirt/corrosion. These things are ready to install. However, I changed my mind and will be going another direction.

    Price for all four is $150. I'm willing to ship, but buyer pays shipping. I would estimate shipping cost at $15-20 based on my research. Please send a PM if interested, thanks!

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
     
    Last edited: Jan 22, 2017
  2. Jan 21, 2017 at 7:44 PM
    #2
    everbiking

    everbiking Member

    Joined:
    Jun 8, 2012
    Member:
    #80308
    Messages:
    5
    Gender:
    Male
    First Name:
    jason
    nc
    Vehicle:
    02 TRD 4x4
    PM sent
     
  3. Jan 22, 2017 at 4:33 AM
    #3
    QMEDJoe

    QMEDJoe Proverbs 3:5-6

    Joined:
    Nov 4, 2014
    Member:
    #141714
    Messages:
    2,352
    Gender:
    Male
    First Name:
    Joe
    Fleetwood NC
    Vehicle:
    2003 black DLX Tacoma,5VZ-FE,5 speed,4x4.
    Fox 2.0 Coilovers in the front and Fox 2.0’s in the rear, Total Chaos UCA’s, Al-lpro expo leafs, K&N cold air intake, TRD headers,Magnaflow catback exhaust,URD short throw shifter, switched out my 60/40 bench seat for some Tacoma Limited seats, Replaced the vinyl shift boot for a leather one, completely soundproofed the cab w/ Frost King. Replaced stock radio with a Pioneer AVH series head unit. Focal component system w/a 10" sub powered by 2 Alpine amps. Weathertech floor mats. Line-X'd the bed. SCS Ray 10’s, Installed an A.R.E. MX series camper shell. All-Pro Apex front bumper w/ All-Pro skid plates all the way back to the Trans. Low Range fuel skid plate.
    I'm just curious what size lift would I need for these to fit on my truck without rubbing for 285/75R16's?
     
  4. Jan 22, 2017 at 7:27 AM
    #4
    BigFishAllDay

    BigFishAllDay [OP] And then?

    Joined:
    Oct 3, 2012
    Member:
    #88250
    Messages:
    897
    Gender:
    Male
    First Name:
    Nick
    ABQ, NM, USA
    Vehicle:
    I have too many Toyotas...
    Everything... and a bag of Cheetos.
    Spacers have been SOLD!!!

    Many people run these with a 3" lift up front, but whether or not your tires rub will depend more on what wheels you are running (and their associated width & offset specs) than lift height.
     
    QMEDJoe likes this.
Thread Status:
Not open for further replies.

Products Discussed in

To Top