TacomaChris's Build :-)

Great rig man, the metallic grey With black looks awesome

 

Oh dear sweet baby jesus.......another taco with spindles!!!!! Looks "fawesome" That stance is exactly where id want mine when i finally get spindles man, nice job! idk if you put it in the info but what coilovers are you using with the 5100s?

 

Thanks! I'm not using coilovers - everything is stock up front except for the spindles and 5100s. Stock springs and UCAs...geometry is the same as stock...I'm VERY happy with it

 

Oh nice i bet you were happy to save some $$$ there! haha I just need to suck it up and pull the trigger on those camburg spindles

 

Worth every penny in my opinion. Install was very straight forward also. Today was the first time I parked next to a stock taco - it made mine look like a damn monster truck lol

 

Got a couple pics of the running boards for you. Let me know if you want some more angles.

 

Nice truck man! You should come on out to the meet and greet in cary today...

http://www.tacomaworld.com/forum/south-east/187254-dec-11th-raleigh-meet-eat.html

 

looks great

 

Great job op !

 

Ahh shoot man - I had no idea or I would have planned to go. I'll have to catch up next time - thanks for the heads up!

 

Hey where did you get those loop to stem rear shock adapters, what are they for and how much

 

iwant to get the exact lift set up you have can you tell me exactly what you got and if located in califorina where u got it?? thank u

 

so cute

 

This x1342703894702398

 

very nice stance! i might have to copy your suspension set up... it looks perfect height. I'm running the pro comp 3" (shocks, coils, and AAL) but just looking at your truck makes me want to switch to what you got.. nice +1

 

I bought the adapters here: http://anyoffroadparts.com/i-4118819-pro-comp-690001-loop-to-stem-adapter.html

Hope this helps

 

Hay man just check the first page of my thread - I listed everything I installed. Hope this helps

 

Thanks - yeah I love the setup with almost 5" up front and almost 4 in the rear...stance is nice and the ride is great.

 

- Wheel backspacing is 4.5"

- Front wheels/tires are out ~ 1 inch compared to the rear (due to the spindles). I have no spacers in the rear because it looks fine to me

- I have the All-Pro expos not the standards (apparently roughly a 4" lift vs 3"). I bought the Bilstein 5125 11" travel shocks...keep in mind the adapters add about 1-1.5 inches of length also

- No probs with the new brake lines. Camburg sent me a set when I ordered my spindles and I also purchased a set for the rear from All-Pro...both stainless braided. Make sure you use a flare wrench so as not to strip them

- The spindles were good to go...I just had to grind a really small section off of the welds so the caliper would fit flush on the new spindles. It only took about a minute using a Dremel with a small grinding wheel

All in all this is what I purchased:
- Spindles w/swaybar provision & front ext brake lines from Camburg
- All-Pro expo leafs, U-bolt flip kit, & ext rear brake lines from All-Pro
- Adjustable 5100s for the front from DownSouth Motorsports
- 5125s for the rear(11 inch travel) from Allshocks.com
- Loop to stem adapters for rear from anyoffroadparts.com
- 3 degree shims for rear & 1/4 inch top plate spacer for driver's side Taco lean from Toytec
- KMC Enduro 16x8 from Amazon
- 285/75/16 General Grabber AT2 from TireRack.com

 

I really like all that clearance you got with the spindles. Looks awesome. I went through your list of parts and you got everything right in my opinion. All excellent parts without getting too crazy. I used 5100's and Eibachs with my bracket lift and it all works well together. I put spindles on my Frontier and they really are the way to go with PreRunners.