1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

The Toyota 10.5" Axle Housing!

Discussion in 'RuffStuff Specialties' started by Dan Fredrickson, Sep 13, 2013.

  1. Sep 13, 2013 at 7:49 PM
    #1
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    What we have here is yet another alternative to the serious axle game. This, like all Toyota axles is built very well and is very reliable with a couple of very good things going for it.

    The first thing I noticed about the Tundra 10.5" axle is the pinion. The Pinion is nearly centered, not very low like a 9", not pretty low like a D60 or 14 bolt but up out of the way which is going to do wonders for your pinion yoke, U joints, & driveshaft.

    [​IMG]

    The next thing that pops up are the 36 spline spiders and that they use the 90 degree pressure angle, not the Dana traditional 60 degree angle. This makes their axles the equivalent of a roughly 37 spline Dana axle which is a pretty damned stout shaft!

    [​IMG]

    Lastly I should confess that I was looking at these 2 years ago and the price was just too high. From Toyota they were $1600 bare and from wrecking yards they were $1000-1100. Over the last few months (September '13 as I write this) the Tundra 3rd members have fallen quite a bit as they started hitting the yards in numbers and today you can get one with a low miles gear set for ~$500.

    Those are the benefits and I would be in the wrong to not mention the one detriment I have uncovered while putting these together. In the US the gearing options are limited with 4:88's being the lowest, however in Australia there are several lower available and I have spoken to several of the US gear guys about importing them and a couple of them are talking about doing so. In the meantime if you run an automatic you should be fine.

    http://www.ruffstuffspecialties.com/catalog/TOY105.html
     
  2. Sep 26, 2013 at 9:11 AM
    #2
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    The best way to start a build!
     
  3. Sep 30, 2013 at 6:00 AM
    #3
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    Ready to beef up your tacoma?
     
  4. Oct 17, 2013 at 8:55 AM
    #4
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    If your going to do it, do it right the first time!
     
  5. Nov 11, 2013 at 8:24 AM
    #5
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    The time for upgrading is now! Build season is upon us! ;)
     
  6. Dec 5, 2013 at 12:01 PM
    #6
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    SUPER BEEF
     
  7. Jan 15, 2014 at 7:49 AM
    #7
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    Lets get this one back to the top!
     
  8. Apr 3, 2014 at 7:11 AM
    #8
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    Let us know how we can help get your rig ready for this summers thrashing & bashing!
     
  9. Sep 3, 2014 at 9:59 AM
    #9
    Dan Fredrickson

    Dan Fredrickson [OP] Steel Hauler Vendor

    Joined:
    Jan 27, 2012
    Member:
    #71582
    Messages:
    700
    Gender:
    Male
    First Name:
    Dan
    Sacramento/Flagstaff
    Vehicle:
    '66 FJ45
    We have had a phenomenal week so far, lets keep it up!
     
To Top