What Have You Done To Your 3rd Gen Today?

you mean you didn't buy your Tacoma to go racing? I thought that's what they're known for. People...

 

right, the trd sport bed decal means its a race car. I will not elaborate

 

Many things over the last few weeks.
-Talons Garage Cat Protection Plate
-Meso Puddle Pods
-Meso V5 Switchbacks wired to DRL
-Re-wired grill lights to turn on with DRL
-AVS in channel vent visors
-Vinyl Hood Wrap
-Red delete-new black bed decals and covered the TRD on the 4 runner wheels center caps with matte black vinyl.
-Course Motorsports no drill phone mount with behind dash fuse tapped charger.

The never ending journey continues with this modification money pit. Good times!

 

Would love to have those puddle pods, but, wow! The install requires WAY too much for me! Half the truck has to come apart just to install two little lights. But, they are really nice.

 

Link to the panel? I want one for my canopy

 

It’s really not that bad. I would say reading all of the posts about the install and door boots makes it out it be much worse than it is. Once I fished the boots once for the puddle pods, the second time around for the switchbacks wired to the DRL’s took about 20 minutes per door. And that’s removing all panels, mirrors, switches to run wires and pit everything back together. Just make sure you test all lights before re-assembly. Definitely worth the time

 

My quest for switches continues…




Next will be cutting out the 3 stock ones and installing the @MESO 6 switch panel. Then comes the part where I actually make them do something…..

 

Yeah I’m pretty salty about it, I am seriously considering charging back the amount I was charged due to the damage. He also put the top hats on backwards.. I usually do everything myself but I did not have access to a sprint compressor…

 

Thanks for the feedback, he also put the top hats on backwards that I had to correct during install… I have the guys number and can contact him through text, what should I say? Deeply saddens me that it is a veteran owned business..

& yes it’s the same on both sides

 

Finally got around to drilling and bolting my fishing rod racks on securely. They were mounted using the mounts they came with, but it was horribly unsecure. Sure the racks locked, but you could just loosen the finger bolts and remove the racks with my expensive rods still in it. Now the racks are bolted through my bed rack (carriage bolts) and when closed and locked the wing nuts are inside the rack and cant be touched.

 

What did you need a compressor for with preassembled coilovers? Unless you swapped out the springs you should be able to adjust ride height while they're still installed on the truck.

 

Swapped out the original springs for 700lb springs

 

Ahh. Still though, a shop should use a wall-mounted unit for springs this beefy, which will leave the adjustment collars easy to adjust. Really not cool. I would never let a vehicle I've worked on leave like that. :/

 

I striped the decals and badges off my 2022 Sport, the third day I had it.
It looks soooo much better without the BS

 

Anyone else install one of these dash panels from Fitztaprint via Etsy or another brand (meso, guild outfitters, ect)? Appears I need to pick up a dremel tomorrow to notch the dash support itself and the rear power window switch mounting hole as the mounting bar tabs are different on each side of the switch. Wondering if the other brands require as much cutting?

 

Installed a new to me voodoo bed rack and a Smittybilt XL Gen2 RTT. Ready for next weeks camping trip!

 

Okay, I marked the inner tab with a silver sharpie, drilled with a 3/32 bit, carved a nib out with an exacto knife and the rear window switch fits nice and snug. I also moved the anytime camera switch to the bottom. The tabs on the back of top blank switch can be trimmed down and I won't need to cut the inner dash support. I'm just going to use that blank switch for a redarc trailer brake knob or the bass knob from my amp, but I probably should have ordered configuration "K" without that upper blank. Oh well. Problem solved and the money I was going to spend on a Dremel can go towards the Auxbeam AR-800.

 

Looked up that course motor sports mount and ordered it

 

I refuse to be free advertising for anyone. The dealer plate frame and stickers are the first thing to go

 

Rear jump-seats & headrests deleted.
Only broke 3 clips