What Have You Done To Your 3rd Gen Today?

They are considerable brighter than the OEM incandescent bulb but not blinding and now they mach the flashing cycle as the LED sequential LED lighting I installed in my mirrors. Note: driver's side done in this pic to compare to OEM on the passenger side.
I did the tail lights as well and needed the resistors also.

$12 KATUR 7440 7443 7444NA 7441 7444 992 Led Light Bulb High Power 3014 54 Chipsets Super Bright 650 Lumens Replace for Turn Signal Back Up Reverse Brake Tail Stop Parking RV Lights,Amber(Pack of 2)

https://www.amazon.ca/gp/product/B06Y4KS99C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1

$12 NATGIC 4pcs 50W 8 ohm LED Load Resistors Decoders for Turn Signal Lights, Headlights, Fog Lights Lamps, DRL with 8pcs Quick Wire Clips (Fix Hyper Flash, Error Canceller, Warning Canceller)

https://www.amazon.ca/gp/product/B07B4ZJPK3/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1

 

Agreed that was my thinking. I was going to go with similar brightness for the brake lights as well. I like my truck bright and surprisingly I've noticed that people dont even seem to mind the amber lights on my light bars being on.

 

Yeah thats part of my motivation to change them. The slight out of sync drives me nuts every time I see the reflection of them

 

Looks killer! Did you paint the OEM skid? Was curious about doing that to mine..

 

Just called my wrap buddy and asked him if he did window tinting. He said he never did but was willing to give it a try. Just ordered a set of ceramics for the front doors. Will post pics if we git-er-done.

 

Chances are high, If you contact KTJO, she may sell it with half of the components, so possibly half the price.
If so, $34 for the front doors sound like a good deal.

I wasn't interested in it before, but the more I look at it, the more I want it. Now it's in my cart, really undecided on the colors.

It is so simple, you could take like 2 minutes per door.
No need to unscrew or unbolt anything, just shimmy the wire down and connect.

 

Perhaps I will contact her. I purchased the Pop-n-Lock for my tailgate from her. Was happy with that product.

 

Here you go:
https://www.amazon.com/gp/product/B077BT6M6Z/ref=ppx_yo_dt_b_asin_image_o01_s00?ie=UTF8&psc=1

If you buy 2 sets you can replace the high beams also. They use the same bulb.

 

I'm in the samw boat as you. I can't decide between blue or white.

 

thats a good point.
with so many people now a days texting and driving , I can use some real bright lights to grab their attention.

 

Or three sets for fogs

 

What is he pushing on with his right hand at the 8:50 mark? Clip under the headlight?

 

They're about 150 miles from the ocean. May have left the door open overnight. If stock sits around long enough, surface rust will develop. Seems like sloppy production to me.
Zim

 

Inner fender to release it from it's pinned location to pop it lose to help with his left hand

 

Does that make the truck a....Pontiac?

 

Liability. Insurance is expensive.
Zim

 

New seal most likely not needed unless you have been in salt water. Just make sure spring on OEM seal doesn’t get dislodged. Install tool can be had at any Harbor Freight. It is a standard bearing race install tool.

 

Sweet! Thanks for the info!

 

No problem. You also may want to grind outer edge of removal tool just a tad if you have any issues getting it behind needle bearing.

 

What lift are you running?