Icon rxt leaf pack

Two to the front

 

That doesn't sound right. check out this thread..

https://www.tacomaworld.com/threads/icon-rxt-leaf-spring-help.588412/#post-20271722

 

Is the front level?

 

This would make sense but, I'm not running option two. It already had the "extra spring" removed when they arrived. Came set as option 1.

The front is level enough FR is 23 1/8 and FL is 23 1/4 will adjust the front a tad more to compensate for taco lean currently have (out of the box) 3 threads on FL coilover and Damn near 3 on the FR coilover will probably adjust to 5 and 3 threads. Running a 650# coil. Measuring from the center of the hub.

 

I just installed the RXT pack in configuration 3 as part of the icon stage 9 kit. I'm running an RCI rear bumper, ARE cap, and decked drawer system full of tools. right now the rear is sitting just about 3/4" higher than the front, allowing for some additional load. very happy with the way they ride both on road and off!

 

That is quite a bit. Mine may be a difference of about a 1/4” at most in the rear on option 2. Def loosen shakle and hanger bolts and retorque sitting under its own weight. Thats the proper way

 

Finally had a chance to get the RXT leaf pack installed today. Went with option two and Timbren Off-Road bumps. I've only driven about 10 miles on city roads with the new setup but man do they feel great! Night and day difference between these and the AAL i had on before. Not sure how much the bumps are helping but from the short ride I took today my ride is a lot smoother. Fronts are 23 3/4" and passenger rear is 24 1/4" and driver 24 1/2" from center hubs to fenders. Now all I need to do is cut the u-bolts down about an inch and get some bumps for the front.

 

Careful not to cut too much like I did. I cut them flush with the cup of the bump can and then installed a degree shim later and the extra thickness means they end just below the top of the nuts.

 

I thought about that. That's why i'm only cutting an inch off.

 

What shims are you guys running? I’m setup with option two with a camper shell and maybe 100 extra pounds of junk. I don’t notice vibrations at any speed. Every time I measure the driveline angles they’re different (iPhone angle apps and user error). I hear some people shoot in the dark, get the 3degree shims and have luck. Even the stock springs had shims. Stuck!

 

alright so i picked up a set from the Icon garage sale but I can't tell if it's got option 1 or 2 installed.

Here's pics if anyone can chime in...thanks

 

Looks like option two Rob.

 

I hope so.

 

It’s definitely not option three since yours only have 7 leafs. The 3rd leaf from the top looks like mine and I’m rocking option two. Hopefully a couple others can chime in to confirm.

 

Thanks man

I'm assuming the aal they include is longer than the option 1 leaf?

A second confirmation would be awesome.

I painted em for pretty sakes right now. Lol

 

Yep, the aal is longer than the leaf that comes with option one. That’s why I think you have yours setup as option two. I’m 99.9% sure based on the photos you posted. There’s another icon rxt leaf thread I believe under the 3rd gen Tacoma thread called “icon rxt leaf pack help” or something along those keywords if you want to post there to have someone else confirm if you have option two. Doesn’t hurt to get a couple opinions.

 

@Rob Daman here you go..

https://www.tacomaworld.com/threads/icon-rxt-leaf-spring-help.588412/

 

FYI.. just measured the leaf for option one and it is 46 1/4”. That was the third leaf from the top before I swapped out the aal.

 

Well I think I have one of each lol.

I measured one close to 46 but the other 3rd leaf is 51 ish.

I also noticed the taper length is different too.

 

Not good