What Have You Done To Your 3rd Gen Today?

Hoping things will be able to be fixed. Definitely super bummed. I like you and many others here love my truck. Just hoping I still do after repairs etc. probably will take a long time to even Get parts. Need a new bumper. Tailgate. Rear passenger body panel. New tail light and probably a new bed since part of the composite cracked. Don’t think there’s any damage to the frame thankfully but will keep you posted when I get everything assessed

 

I think I'm about $6k in mods at the moment. Last night I priced out some Fox Elite 2.5's with Deaver N98's and UCA's on Accutune's website. With 5 wheels and tires it was about $10k. Then I started looking at bumpers and brake upgrades. It definitely adds up quick.

 

Added a little bit of accent

 

Yes I did that as well. Had to put a spacer on the back one and cut the threads down a lot. Two different lengths.

 

Nice. You may have seen this, but my Group 31 battery tray install can be found over here.

 

Thanks for the photo and feedback! It looks awesome! Can't wait to get mine installed. It looks like it settled nicely.

 

Excellent - how do they compare to try FOX shocks put stock on the PRO?

 

Got the TRD intake and made a quick install video!

 

Seems the only feathers ruffled here are yours.

 

Installed a dashcam with the Dongar Tech power adaptor.

 

Any Hyperflash issues?

 

Some LEDs are CANBUS compatible which means they have the resistor built-in. I had to put this type in the rear signals of my FJR1300 since adding resistors to the wire harness would have been a PITA.

 

Yanked the driver door panel off this weekend and replaced the cheap foam rattle seal with some properly thick felt strips to get rid of rattles. So far so good.

Threw in the Z Precision cupholder this weekend. Muuuuch wider and deeper than the stock piece. Really nice build quality too since they're injection molded and have perfect fitment.

I made a rubber insert to reduce rattling and threw a layer of Noico on the underside to help insulate and reduce cabin noise.

 

Lol I’m good Billy

 

I did the same thing months ago. (See attached). The only thing on that list that I cannot remove or undo is the front bumper and detailing I had done to the truck. Everything else can be detached by unscrewing, un-mounting, popping off or peeling off with a little sweat equity. Would I? Nah...because I'd probably get ten cents on the dollar for what it's worth.

Currently, my total is hovering around $6,500

 

I need to do this, got a pic? I was imagining wrapping those wires with one sided sticky molding stuf.

 

I didn't take one. But when you pull the door panel apart you will see a very thin very weak foam strip running up and down the edges of both doors. This can be peeled off (in my case cleanly once you get it started) as one big strip. Then I replaced those entire sections with better, thicker felt strips. This is where most of the door rattles come from - rather than fixing them one by one doing the whole section seems to get rid of most of them. Just butted them right up against the edge of the door panel and it's just a hair thicker, eliminating those panel-to-door rattles.

Felt strips I used: -

$9 Shappy 2 Packs Felt Strips with Adhesive Backing Felt Tape Roll Non Slip Self Adhesive Cuttable Furniture Pads for Protecting Hardwood Floors, Chairs, Wall(Black,120 x 1 x 0.12")

2 Packs Felt Furniture Pads Heavy Duty Felt Strip Roll with Adhesive Backing Adhesive Felt Tape for Protecting Hardwood Floors Chair Wall Protector(120 x 1 x 0.12 Inch,Black) - - Amazon.com

The 2-pack is just a little more than enough to do 2 doors.

The wiring itself doesn't rattle too much, but the clips securing it do. Adding a bit of butyl deadening around those to secure them to the door better helps a ton.

Sheeeeeet that doesn't even cover my suspension lmao.

 

Nice! I just reached out to zprecision to see if they make these for the MT trucks

 

Damn. I knew I forgot items. Need to add console and glove organizers, light switch, relay harnesses, and key fob.

I didn't include accessories like the straps, shackles, or first aid kit. Maybe I should.

 

As far as I know they do not have any MTX support yet. This has been super popular though already so we might see more parts from them in the future. I would be in for deeper rear cupholders too if that's possible, those are pretty pathetic.