Colorado Trading Post

My topper is officially for sale. It's an ARE for a 6ft bed 3rd gen. Back and side windows flip up. Front window flips down. I added custom bug netting to the side windows, and a latch catch for the front window to prop it open slightly in cold weather. All the mods can be easily removed if desired.

It's in good condition with few tiny chips around the bottom edge. I just replaced the seal with an ESI triple bulb seal. And I just replaced the gas struts on the rear window. Asking $1000.

@TacoTimbo can probably paint it for you if you want a different color.








Front window catch: https://www.tacomaworld.com/threads...3rd-gen-today.399305/page-14063#post-29870172

Bug screens: https://www.tacomaworld.com/threads...3rd-gen-today.399305/page-14063#post-29869779

 

Letting go of a MTB Front Wheel mount thingy for Toyota bed rails. Reference this thread

The mount supports 15mm x 100/110mm TA front hubs. Used a few times but no longer have a use for the thingy. Asking $40 for OG mount and bolts. For an extra $10 I can provide a 9/16" thick Aluminum Block Spacer and longer bolts to allow mounting the wheel thingy to work with a Topper.

 

I have two awning that I am pulling off the truck, both in pretty good shape, both covers have some tears but are sealed up from any weather, small hole in one but taped and as seen in photo. Yakima slim shady small hole but taped 77”x77” and a Roam Size 4’ both have ground stakes and bolts,no bracket, asking $50 each, Located In Longmont

 

NM: $100 neoprene 1st gen seat covers. I wouldn’t worry too much about the stains - I bought a used set for my 2nd gen that was similar and after soaking in the bathtub with warm water and scrubbing some with some soap, they looked almost like new.

https://www.tacomaworld.com/threads/100-coverking-neoprene-seat-covers.854990/

 

SOLD

 

**SOLD **

 

I have 1 extra Loveland lift ticket. Valid this season only, came from a 4-pack.

$40, pickup in West Greeley.

 

Not Mine:

1st gen DCSB fiberglass tonneau $250 in FoCo.

 

Not Mine:

1st gen DCSB ARE mid-rise fiberglass shell WITH rear "camper" door (replaces tailgate). $1900 is a bit steep unless you REALLY want this specific one. Gold color.

 

JACKPOT. Not Mine.

$150 including round bar roof rack with rails. White 1st gen DCSB shell. Looks to be an ARE. Up in Cheyenne.

 

Interested! DM'd you!

 

Hand pump for RV sink. Brand New, never used. Pumps on both strokes from holding tank, or can be used with city pressure (requires pressure reducer, not included) by simply pushing handle down.

Perfect for that overland build, wedge tent, outdoor kitchen, etc...

Around $50 new, first $5.00 takes it. Come get it.

 

Not mine. Unicorn V6 single cab.
https://fortcollins.craigslist.org/cto/d/fort-collins-1996-toyota-tacoma-sx/7839249810.html

 

Or have this v6 swapped truck.

Pros: Clean, nice seats
Cons: Auto, you're trusting a stranger's swap job, mismatched upholstery
Neutral: Also has a 4runner dash

https://cosprings.craigslist.org/cto/d/peyton-toyota-tacoma/7838963531.html

 

The '96 has the best looking front clip.

 

Speaking of V6 Single Cabs...

 

People selling these really aren't advertising well.

 

Selling some 4.30 front and rear ring and pinion gears for a third gen taco. I bought from another member to put into my TRD offroad automatic but sold the truck before I could. Came out of a TRD sport manual with 8k miles. will fit into 8.75" diff 2016-2023 Asking $500

 

Location in CO?

 

Maybe still (from 2019)