What Have You Done To Your 4th Gen Today?

Corrected the shaking hood they should have done this from factory.
Found on Amazon
Automotive Door Weather Stripping 10Ft Car Door Rubber Edge Trim Seal Strip Gasket with Top Bulb Easy to Install for Car Bus Camper Boat RV Truck Doors and Home Applications

 

FYI, I chose to place the camera on the driver's side edge of the rear glass as I have the sliding back glass window that slides to cover the passenger side of the glass and I didn't want the camera in the center rear view area when looking in the rear view mirror. Also, be REALLY careful routing the cable down the A pillar. There's an airbag there so you have to disconnect the battery, remove the bolt at the top of the pillar trim and carefully pull the upper part of the trim off. At that point you'll see that you can route the cable on top of a couple of metal brackets that sit above the airbag. That keeps the cable from interfering with the airbag should it be deployed in an accident. From there you just carefully route the cable past the bottom of the trim panel to the left edge of the dash and then down to the rocker panel. The rest is easy.

 

What exactly was added and where? I cannot tell from pic…

 

Won a give-a-way from Muslogy Auto that sells aftermarket stuff for the Tacoma. They offered someone all items bought during Amazon prime day sales money back so I got their center console cup holder inserts and the organizer. I am very happy with their stuff even before I won the give-a-way. Looking at getting some more items from them.

 

Another option is to use existing OEM dashcam connector in the overhead console area.

If your camera uses 12V skip the voltage converter

https://www.tacomaworld.com/threads/installed-dash-cam-using-factory-pigtail.830200/

 

It ended up being a two beer job, and I think I overtorqued the clamps a bit, but I managed to get my Diamondback Switchback "factory second" installed. Damned if I can tell what the blem is that made it a second. So far so good, and it will definitely keep sticky fingers away from my snowboards and backpacking gear...

 

Changed my oil for 2nd time, 6000 mi. I made less mess this time than last. The filter is on front of the engine and the drain plug is in the rear so it can get messy with just one oil drain pan that can't be in two places at once that are both dripping.

 

That’s good to know as I just have the regular mirror.

 

I added the weather stripping to the section in the yellow circle.
Any help you need just ask

 

what are the big cup holders in the back? i need some

 

DYLEN car cup holder expander it’s called. I got them from Amazon.

 

Plastidipped the front emblem and added some low profile wind deflectors (truck needs a wash)

 

What running boards did you go with?

 

The project nears completion of Phase I.

Ditch Lights
Trailhunter Rock Rails (installed today)
Nomad Convoys
Toyo AT3's
Cab Roof Rack

A few misc items (wiring, a couple lights and mud guards) is all that remains.....for now.

 

New boot goofin’ on the Pro.

RRW RR7-h
17x8.5 +25

BFG 315/70/17

Only change needed was removing the crash bar in the front wheel well.

 

How do the Load Range F tires feel?

 

can obviously notice the weight difference. But as far as ride quality, it's not bad at all. I was concerned a bit I'll be honest but pleased so far.

 

BOUGHT ONE LAST NIGHT!!! I'm back, baby! I got rid of my 2009 TRD PreRunner about 4/5 years ago, but now I'm back with a new 2024 Blue Crush TRDOR 4x4! I lucked out and this was the only one in that color that the dealership couldn't sell for a bit due to the brake line recall. My wife and I were literally grabbing something to eat on the way to go pick up a new 2024 Ford Bronco Black Diamond edition. But I couldn't be happier to be back in a Taco! As stupid as it sounds, TW is one of the things I missed the most!

 

Finally got new shoes. SCS Ray10 on 285/75/17 Open Country AT3's.

 

why not the Bronco? you made right choice of course