What Have You Done To Your 3rd Gen Today?

Does anyone know whether our trucks already come with PTR11-34070

$383 TRD Rear Sway Bar

TRD Sway Bar fit in it's stock configuration? (also whether the said part fits our model).

 

That part number Says it won't fit 2016 Tacoma, it's for the Tundra.
Not really something you'd want on an OR TRD. Unless it had disco links on it then you would have the best of both worlds.

 

Agreed! I got 3 1/8" with the 888 coils alone. The Billies are set at 0!

 

whatcha gonna do with it? got any pics?

 

Ordered 700# King springs from DSM in prep for the Pelfrey bumper that I'll be ordering soon.

 

Found out this morning after owning the truck for 9 months that I have a factory installed alarm system. It was not listed on the Mulroney. Surprised my service manager also.

 

This sorta reminded me of a Honda Gold Wing I bought back in Dec. 2005. It was the base model, but still had all the buttons for things like a CD changer that mine didn't have. Somehow in the sales process, they forgot to mention a few things. On the 40+ mile ride home, I saw a button and thought, "Wonder what this does?"
It had cruise control! LOL

 

So got around to installing my new

$323 ARB CKMA12 On-Board Air Compressor High Performance 12 Volt for Air Locker Differentials and Tire Inflation

ARB CKMA12 Air Compressor with the ARB (171302) Inflation Kit and ARB (

$48 ARB605 A Tire Pressure Monitor Inflator and Deflator with Analog Gauge and Flexible Hose in Blue

ARB605) Blue Inflator with gauge and braided Hose. The thing works great, fills a tire up from 20psi to 40 psi in a little under 2 minutes!

Here is a little Video of it working:
https://www.youtube.com/watch?v=_fwUFy9MOvc

Final Mounted Pics:


Before the Install:


The bracket I made to mount the compressor and switch:

 

Nice very nice!

 

Where the pavement ends..

 

Thanks Vincent!

 

So I'm going to be installing my new rigid fog lights soon. I was going going to just wire them into the stock wires and switch but then started reading about flicker? Anyone know this to be an issue. If so I bought a switch to use with the rigid wiring harness then I guess I could have them on anytime I want so I'm leaning towards this. However the only blank I have left open is in the center below the climate controls. Does anyone know or have you gotten to this panel and how so. I don't want to just start pulling at plastic pieces. Lol. This is the switch I ordered so it should just snap in if I can figure out how to get at it.
http://m.ebay.com/itm/361560274505?fits=Make:Toyota

 

Very nice!

 

Nice! What lift did you get?

 

Ya I left them on and I didn't bother taping anything besides the Toyota emblem. I was able to peel off the over spray on the calipers. I did 4 coats with 20 mins between coats.

 

Do you have to respray the lug nuts if you remove the wheel?

 

That is a deal compared to Montana $410

 

My guess would be yes. I'm hoping I won't have to remove the wheel until I buy new ones though

 

Installed Opt7 LED low beams and fogs. Also plasti-dipped the grill while I had it off.

 

Just installed my k&n 63 series intake. Holy crap its loud as hell when I floor it. It may be a little too loud for me but I'll wait and see how it sounds in a little while. Install was alright; the instructions are wrong in some places and mislabeled with parts that don't go in the area. Gives it a nice rumble when accelerating normally.