Cali Raised Led Lighting /Brackets*Great Affordable LED Bars And Pods* And ROCK SLIDERS

Just finished installing my new ditch light brackets and fog lights from @CaliRaisedLed They are AMAZING. The fog light brackets didn't look like they were going to fit flush with the bumper until I tightened down the bolt on the back and now they fit like a glove! At first I was debating whether to get the amber leds or the white.. but the amber was by far exceeded my expectations. Also installed the 2x2 OSRAM led pods on the hood. Looking forward to getting a set of extensions for my ditch light brackets to add more lighting! Only thing that I didn't get was a Caliraised decal or sticker to add to my collection along with the APEX fab sticker.

 

This might be a noob question, no it definitely is; but my single leg wiring harness came in the mail and I just got it out to take a gander at it. What are the second set of connectors for? @CaliRaisedLed

 

Looks like it's a double leg then, just need to use the other ones or you can cut them.

 

Hey Bryan

 

Placed my order, can't wait to get them!

 

Somehow , I JUST discovered these lights! Im wanting to order the amber's for my '13 with the brackets and plugs. Question is: do they cast as much or more light than the OEM fogs?

 

100% will cast way more light an the OEM's. We made these so you can have an led performance for your fogs

 

@CaliRaisedLed Hey, what ditch lights should I pair with my 32 inch stealth combo with the amber filter? They are on the way but I am going to use this in some intense snow and bad weather?

 

I would definitely go with the 20w pod facing to the ditches and get amber covers for them. Or just go with 18w amber pods

 

Roger that, I am going to go with them 20 watt OSRAM's. Putting in the order today or tomorrow. Thanks for the help, sounds like my bar and cover are on the way with the switch. I am heading out to Bend Oregon next week with a nice DSLR and will get some good pics for you guys you can post.

 

Sweet! Can't wait for the pictures

 

Yo yo!

 

OK I have tried everything to get through the firewall on the drivers side. The large round rubber piece has a small nipple near the bottom... has anyone had any luck getting in through there? Three times now I have secured a garage to work on it and three times I have failed. And I have run wiring through the firewall before.... I have 2 antenna wires and a full 10Ga 12v pair run through already. Really frustrated right now... light bar has been on the truck for nearly a month now and I can't use it.

I have a TRD OR AC if that makes a difference.

 

I personally have tapped my wire to a coat hanger and pushed it through like that. Try that

 

My friend suggested the same thing.... I am afraid of piercing a hole in the main wiring loom... I kind of thought after I cut the nipple off the end the wiring would go through pretty easily, but it's like there's a blockage on the inside. I get th through about 2.5 inches and it just stops. Did you meet with resistance? I am using a very stiff zip tie because I know it wont cut wires.

 

With all of mine and other installs I have done there been a little resistance, but will go right throw after messing with it for less than 5 minutes

 

@CaliRaisedLed got the 32 inch stealth and the 20w pods coming what add a fuses will I need to install both of them to come on in the cab? Also tap them both to the taillights I am thinking?

 

With the bar it comes with a wiring harness which has a relay and fuse already hooked up for you. For back up light that's what most people do just tie the positive and negative to the tail lights

 

@CaliRaisedLed If I am doing the pods and the bar can I tap both of them to the tails? Sorry I am a super newb at this lol