What Have You Done To Your 3rd Gen Today?

Thank you very much! I install almost everything I sell and take mental notes during the process. I also try several methods to determine the best one. 30 years experience writing IT manuals helps!

 

Next step in blacking things out is to swap out the fog lights. There is a GB still going on for the Morimoto fogs that will take out those chrome orbs for ya. They also have the added benifit of allowing you to see better in the dark too!

I like the basic decal swap to grayscale. Where'd you order it from?

 

So not today, but yesterday I got me a new lift, wheels n shoes. Icon stage 5... Only 691 miles on her!

 

LMAO. Our dogs haul firewood in sleds to the house, Huskies like to work. She is a puppy and will be just fine although she and I were not on speaking terms for a couple of days...

 

True dat! I’m waiting for a deal on some BD squadrons. I’m a douchebag so yellow LEDs are good for now.

Thanks! Got the decals on eBay.
https://m.ebay.com/itm/Toyota-TRD-2...Stickers-N7-/192323150213?txnId=1490132054009

 

Started the demo on the kitchen today. Took off bead board and some ugly ass 1980s wall paper underneath. Debating on just taking it down to studs or skim coating it and painting.

 

Did you remove the wheels from the truck to dip, or did you plastic behind the wheel while mounted...or maybe the easier question. What was your process? these came out good.

 

Thanks. I am really happy with the results. Here is what I did:

1. Taped the lug nuts with blue painters tape
2. Put paper/plastic behind the wheel
3. Warm the cans in very hot tap water before/during use. This will make it spray more evenly and give you a smoother finish. I think this is the most important step to ensure you get a smooth finish.
4. Get a spray can tool, helps control the can and is much more ergonomic
5. Use lots of coats
6. Cover the fender areas with something to limit overspray. I can't see it, but I can feel it there. It will clean off easy I'm sure, but it is an extra step
7. I would tape the tire approximately .5-.75 inches from the rim. The thick overspray close to the rim is very easy to peel off. But as it gets thinner, it is a little more difficult to remove from the rubber.

 

Dropped the nerf bars and finally got the sliders installed. Opted for weld-on 4x Innovations. Between measuring and welding the legs and mounting plates, then prepping and painting, then welding to the truck, the process took about a week. Not the best pics, but good enough.

 

I used a hole saw to cut a 6 inch hole in my front splash shield and used some scrap pieces of thin sheet steel and aluminum strip bent by hand to make an access port for oil filter changes, requiring the removal of only one bolt instead of four bolts and the shield.
It’s sturdy even without utilizing the one bolt for securing the door.

I might purchase proper skid plates before the next oil change. If not, this will do for now.

 

Thanks! I did the bumper and liked the results but was less worried of the look as it will eventually get replaced. But the rims I like and want to get right on the first go. I also want to paint the center cap tan to match the truck and do something different. But don’t copy me, we’re both in SoMD haha

 

threw on a matte black hood decal

 

Icon Stage 1, Icon Rebound 17" wheels, Demello Offroad Rock Crusher Slider (replaced Westin steps), 275-70-17 BFG K02 tires. No rub after alignment.

 

Ok, let's see, there's not a damn thing in that post over there that you listed I wouldn't eat or drink.

Love the boots too!

 

Was browsing around today and saw that mobil1 has their $17 rebate active again. That reminded me of something else I needed. Ended up ordering the Toyota aluminum oil filter housing and a Bulletproof Fab front recovery hook to replace the wimpy stock Sport recovery. Also picked up a 3 ton 5/8" shackle to use until I trim the Pro skid to clear the 3/4" shackle. Not bad for $108 total after discounts. Now to find out who has that mobil1 oil on sale. Rebate good through May 31 but might as well stock up for the next oil change around Thanksgiving (if I can put on another 6k miles and get to 24k miles by then). That should give me time to pick up a Fumoto.

 

Said I’d post a pic.

 

^^^ @AtlasPilot you have a motocross playground right across the street from your driveway! Why would you feel the need to load up your bike? lol

 

Are you serious!? Volks!!?? Damn you went through 3 sets of wheels already lol

Or is it more like 4 or 5 sets?

 

yes I did! You have a great memory. haha.

I'm done. I even said so in the video.

 

Trick we used to keep the tires clean: