SCS SR8 wheels 16x8 & 17x8.5

Thanks. Topper actually comes that way from the factory.

And yes I'm running 265s currently. Looks are subjective, but I think they look just fine with a modest lift.

 

I’ve been scrolling through the hundreds of wheel and tire setups on here and everywhere else online which makes decisions even harder. There’s so many options that I feel are better than the stock trd off road wheels that came on my truck. If I go sr8’s it’s either gunmetal or matte bronze on my super white. I cannot make up my mind for the life of me!! Wonder how these wheels would hold up in the salt belt?

 

Ok guys, these are the wheels I wanna get for my mgm dcsb sr5.... just debating on the 16x8 with 4in bs or the 17x8.5... gonna run a 265 tire.

 

If I had to do it all over again I'd do 17" rim. Better tire choices.

 

Cement with Sr8 dark bronze?
Anyone?

 

Help!

I'm new to the Forum. I just ordered a 2020 pro and want to know if the SR8s in 17 x 8.5 10 mm offset with 265s will fit without any modifications?

Thanks...........

 

Maybe just take your front mud flap off? Other than that maybe some minor rubbing on the plastic moldings

 

Bet you say that to all the Third Gens.

 

Well if he was going 285s that's all that needs to be modified

 

Oh man I'm not sure what wheels I want. I was deciding between the sr8 or f5's. Both killer looking wheels!

 

Will 16” SR8s fit on a T4R5? Asking for a friend.. heard the break caliper is too big.

 

If T4R5 refers to a 5th gen, they require 17" or larger wheels to clear the calipers.

 

Here are a few pix of the new wheels and tires on my 2004.
Minor rub on the fender plastic at full lock while reversing. I will wait until the suspension settles to make any big changes to the area that barely rubs.
My setup:
OME 882 front struts
JBA uca's (std, high caster)
Dakar rear leafs with aal
3/4" diff drop
1/2" carrier bearing drop
All new bushings/shackles blah blah blah...

Exactly 40" from the ground to the middle/bottom of the front fender.

Hope these pix and info will help anybody out there trying to get a visual on how these fit!

SCS SR8 Gunmetal 16x8, Mastercraft MXT 285/75r16



The wheel and tire still tuck nicely into the fender well when the truck is flexed. Perfect fitting wheel in my opinion!

 

Thanks @Taco Roofer - I was going to ask about running 32+ tires with the JBA’s and the offset with these wheels.

 

Glad that helped you out!

If you have any other questions feel free to ask.

 

16x8 Gunmetal w/ JBA UCAs
Falken Wildpeak AT3W 265/75r16
6112 front @4th notch and 5160s rear w/ Wheeler's add-a-leaf

 

Rough country 9000 shocks front and rear, adjustable coilovers up front to 2.75in of lift, 1in rear block lift, Baja kits uca, 17x8.5 scs sr8 gray, 285/70r17 Toyo A/TII

 

Great pix and info in this thread! Thanks to all that have shared. Only issue is... I just cannot put my finger on the setup I want for my speedway blue smh. Thinkin 17” matte gunmetal Ray 10’s because I’ve been running 285’s for a while. I did just install this topper though and it’s getting color matched to the truck which will help a lot. However, my eyes are now playing tricks on me and making the 285’s look small.
Any recommendations?

 

I’m looking to buy a set (4 or 5) of SR8 in the Brushed Bronze color!

 

I think gunmetal or even the matte gray would look solid with that blue color. Bronze and blue also looks great as well. Just depends how flashy you want to be. I had a really difficult time deciding on what color I wanted to go with.