Baja Designs: General Discussion Thread

You might be able to find some at a local hardware store, but we're always willing to send some out if a customer needs it.

 

The Rockstar Garage grabbed some clean shots of this second gen Taco out in KOH 2020! Rocking a 20" S8 light bar behind the bumper, a few pairs of Squadrons, and a pair of S2s.

 

COVID-19 Notice:

March 19th, 2020:

CA State Governor Gavin Newsom has issued a "stay home order" to all California residents. Baja Designs has temporarily paused most operations until further notice from the State.

Select departments will continue to work from home and can be reached through their normal email addresses.

We are doing everything possible to fulfill orders at this time. The health and safety of our employees, partners, and customers is of the highest concern to us and we thank you for your patience during these unsettling times.
We'll be back soon! ♥️​

 

Stay safe. People can wait for lights.

 

Here was a fun little project we did

40" Onx6+ Spot
S2 Pro Wide Corner
x5 Lp4 Driving Combo
20" S8 Driving Combo
Squadron Sport WC

Also not pictured is
x2 Rock Lights - scene/wheel well
S1 Work Scene - scene
S2 Sport Spot - chase

 

If hood glare is too bad I found a very simple fix is just move the light back a few inches. Made it go from totally unuseable to the best light ever. This is an S8 in all spot.

 

Definitely a good move! I did recommend him to mount it further back, similar location to where you had it mentioned. I definitely wanted to play around with his setup out in the desert to aim lights and change out a couple lens'!

 

Those LP4s fit nicely in that bumper! Thanks for sharing.

 

https://www.bajadesigns.com/home/together.asp

 

@Baja Designs So I have a set of S1 lights my setting up for my Ditch Lights. I know it has been mentioned but I didn’t find a solution I was sure about. They are grounding to the ditch light brackets I believe. If I connect just the positive wire the lights will turn on. Is this an issue for them to be double grounded? I saw maybe cut the negative wire, and I saw isolate the lights from the mount using a rubber washer.... I wasn’t sure the correct solution.

 

My OnX6+ is like that as well. I have it positive and ground both connected through the harness, and have for awhile, no issues.

 

The way our lights are designed, the circuit board is grounded out through the housing. In a situation where customers mount their lights on a metal bumper or mount, it will turn on the light when just the power wire is hooked up. This does NOT damage the light, and would be considered a normal reaction. We always recommend grounding out the black wire so we ensure the ground is strong and we don't run into issues down the road (dirty ground, corrosion, etc.).

 

Thank you just making sure I’m not popping fuses.

 

I added all the @Baja Designs lumens back in October

• In front bumper:
  • 1x OnX6+, 20", Straight, Amber, Driving/Combo (1x SKU 452013)
  • 2x Squadron Sport, Amber, Wide Cornering (1x SKU 557815) - already had these installed
• Behind grille:
  • 4x XL Sport, White, High Speed Spot (2x SKU 567801)
    • Installed with 3x OnX6/S8/XL, Wire Harness Splitter (3x SKU 613608)
    • Installed with @JLee BAMF behind the grille bracket
• As ditch lights:
  • 2x S2 Sport, Amber, Driving/Combo (1x SKU 547813)
    • Installed with @Joshp767 RCI Metalworks ditch light brackets

Big shoutout to Chuck at @ShowstoppersUSA for the great prices and awesome customer service! I definitely recommend you reach out to him for part needs.

 

All the lumens!

Thanks for sharing.

 

Full spaceship mode at this point

 

For those Tacoma owners, that own a Polaris RZR! Here's a new product drop.

NEW PRODUCT ANNOUNCEMENT

Polaris RZR Turbo/S 16+, XP1000 14+, XP900 15+, 30” Roof Mount Kits

Introducing a clean and simple bolt on solution for the Polaris RZR Turbo S (18-On), Turbo (16-On), RZR XP 1000 (14-On), and RZR XP 900 (15-On). Our standard light bar brackets line up perfectly to the Turbo S OEM roof mounting locations, so this will be a big seller based on the user-friendly installation and price point. This kit comes plug and play with all the necessary hardware components, wiring harnesses and light bar. For the S8 option, we will be including a Polaris RZR specific add-on wiring adapter that will enable users to activate the amber backlit LEDs with a keyed power source. Service technicians and DIY customers alike can breathe a sigh of relief with this race ready light bar setup.

Configurations:
44-7181 | Polaris RZR Turbo/S 16+, XP1000 14+, XP900 15+, 30" S8 Kit, Retail: $919.95
44-7182 | Polaris RZR Turbo/S 16+, XP1000 14+, XP900 15+, 30" OnX6+ Kit, Retail: $1,149.95

 

Glad we could assist! It came out awesome!

 

Anyone have any tips on making your own harness for a Onx6 20” bar? Wiring it to an Spod if that helps. Mostly wondering about wire gauge.