What Have You Done To Your 3rd Gen Today?

Damn that’s a good looking truck!

 

I purchased the Y adapter for the ECT/TRD pro harness also from tacomabob. I expect it this weekend. I very seldom look at the buttons on the left side of the steering wheel but noticed I have a blank spacer that will fill the void nicely. Only issue I have is reading others posts. Some put a USB plug on this side to charge phones. Decisions...decisions.

 

You don't have to break the 'alligator' clips or bumper tabs if you remove the bumper end assemblies. I used two 90 degree scribes to get under the clip on each end and they pull right off. Then you can install the clip on the new caps. Black caps are only $50 on eBay, half the price of those skinz....

just make sure you align the bumper ends before you tighten them down (bring them close to the body, there's a bit of room to align them)




https://www.ebay.com/itm/Rear-Bumpe...-Set-For-Toyota-Tacoma-2016-2020/284058636922

https://www.tacomaworld.com/threads/16-tacoma-bumper-cap-removal.404082/page-12#post-24904789

 

In House Fab is based in Queensland AUSTRALIA. I believe the snorkel is a similar copy to the Hilux N70 and N80 you see on the site. I am not sure about that, just my guess.

@JDSmith Sloop Motorsports sells the In House Fab here in the states. Through email conversation with Sloop I found out they are sold out here and could be another 6 months before they get any here in the states.

 

How long did you wait and did you get it on line? I paid a 100.00 to be on the list for when it comes in sept. Looks great and very solid...

 

I found the perfect setup to stop my hand sanitizer from clunking around in the door compartment. It’s been driving me nuts for the last year. I moved it to the center console molle panel.


A germ-X 8 oz. bottle fits perfectly in the OneTigris Single AR Mag Pouch. It also has Velcro on the outside for a patch.


Here’s the link for anyone interested:

OneTigris Single AR Mag Pouch...

OneTigris Single AR Mag Pouch Rifle Ammo Holster with Detachable Mag Sheath (Black)

https://www.amazon.com/dp/B07W5G2LCH?ref=ppx_pop_mob_ap_share

 

On my way to the dump hillbilly style after a little spring cleaning...

 

$650 Body Armor HiLine Series Front Bumper - TC-19339

https://www.4wheelparts.com/p/2021-...mper-TC-19339/_/R-BKKM-TC-19339?ppcfon=1&gp=1

 

Thank you for your service!

 

Starting a water tank build inside the alucab- DIY 8020 alu cabinets begin next week

 

I used this. Works great. I use it between coats of Turtle Wax Ceramic Spray Coating.

 

This is what I ordered from Morris 4x4. I thought it was a good deal considering you get the light bar and shackles if you are looking for those items as well. However when I bought it was $718 + tax. Now it’s listed at $799 + tax
https://www.morris4x4center.com/bod...-with-20-led-light-bar-and-black-d-rings.html

 

just the passenger side front fender

 

I so need this panel. I have all small switches except for the clutch override switch, so I need the single tall switch.

 

And you hooked me on that stuff, too!!

 

Installed the 3TPAM

https://expeditionessentials.com/co...ta-tacoma-3rd-gen-usb-powered-accessory-mount

1.5hrs, the alignment took the bulk of the time.

 

Put the right size switch in!

 

Installed Oem TRD intake flow accelerator snorkel (PTR03-35090-AC) ~ $7.39.

However mine did not came with a notch on top so I cut that out with a utility knife.

 

Hi- so why did you cut a notch out Just asking, because if installed properly no notch is needed for the V6.

 

Exclusive PRO owners wax! Dayum!