1st Gen Lunchtable Thread - General Discussion

Got em

 

could be? its chrome package
i was not expecting these to break, apparently they are supposed to slide around and line up with the holes in the gromments i had to bust out to clean.
well these were not sliding except for the top one.
i guess that 22+ years of NEVER removing them had a ton of sand and mud turned to dirt lol and caked in them
kept them under the faucet to turn muddy and slide them to clean and it snapped
also noticed a few others had fractures on the plastic!

 

damn $6+ a piece!
i may need 10 to 20 of them

 

it says this on the description


Included With Wheel Opening Molding.
that must be why these moldings are SO DAMN xpensive!

 

Once you are certain about the part number, then google search on "Toyota 75049-35050". That will usually find a set at a lower cost.

 

$16 Genuine Toyota 75049-35050 Molding Clip Sub-Assembly

https://www.amazon.com/Genuine-Toyota-75049-35050-Molding-Sub-Assembly/dp/B01DYHHRHE

$15 each on Amazon yikes!

 

@BartMaster1234 If you ever experience a MAF problem, the ones from that era can be repaired if you are handy with a soldering iron.

I have at least 3 good working MAFs (that I picked up from salvage yards) in my workshop that I keep on hand and rotate around between the two cars that use them whenever I change the air filter. I do that because I don't wan't to be caught without a good working MAF in stock in the event that one should fail.

Causes for break down come from:

1) The silicone seal around the top cover breaking down and allowing water into the MAF.
2) The wires from the plug socket to the MAF circuit board work loose and need to be re-soldered.



Here's a video on how to repair Nissan MAF wire connectors.

https://www.youtube.com/watch?v=0nnigpKWFnY

 

Made by a hater. The 6.0l never mixes, it pushes exhaust out the coolant system

 

i just had a moment of clarity regarding the bees knees known as POR-15

 

An epiphany? Care to share?

 

since POR-15 is not UV resistant and requires a topcoat
what happens should that top coat get chipped and exposed POR-15 lies underneath
UV radiation will hit that exposed spot more than likely and then the peeling and decay starts slowly

Moment of clarity definition is - a time when a person suddenly understands something.
An epiphany is an experience of a sudden and striking realization.

could be either?

 

Where are you applying POR15?

 

i have not applied any yet and do not have any in my possession to test

but there maybe a few spots underneath that are going to be near impossible to reach and clean properly so I will have to find a different product to use in those spots

 

Where do you plan on applying it then? If it is to the frame, which I believe it is, when will your frame ever have extended periods where it is exposed to direct sunlight?

 

sun glare off of the snow and mirror like streets i am thinking for one, the streets here were VERY shiny a couple days this week
assuming that UV radiation bounces around like i think it does on ski slopes?
but i am not knowledgeable about that stuff

 

The chances that that would cause the decay to start after a chip are ridiculously low. You are overly paranoid about this shit. Clean it, paint it, FF it. Rinse and repeat. That's about the best you can do.

 

a 3rd genner i know told me i can solve this by getting a new truck every 3 to 5 years!

 

Yeah, you could. But do you want a car payment for that long? The only thing better for your truck is to have a winter beater and keep the Taco garaged except for sunny days in the summer.

 

No need for fancy por15 paint thats not uv safe. Rustoleum from Homedepot or Valspar Anti Rust Armor from Lowes will work just the same. Good prep, primer, paint. Wait a few weeks then fluid film.

 

i do have a winter beater of the same age and mileage but it doesn't get around in a foot of snow!
and now that car is near dead with a perforated fuel tank among other things so am car shopping for something else
i bot my Tacoma to make it through the mid west blizzard months without fear of getting stuck which i only have once!


i sprayed FF all over the numerous body panel perforations on Corolla
its a true ghetto car but have had it longer than the taco
the heater in it is top notch!
crank windows
no clock no fancy nothing other than AC
did not even have a tape deck until i swapped my oem tacoma tape deck in there