1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site
    Quick Links: ARB RD121 air locker - NIB Bhlm headlights for sale no broke tabs 2.5 "Lift kit with super springs! SOLD FS NorCal: MGM Leer Camper Shell 5' SOLD. [SoCal] Anzo U-Bar Projector Headlights 12-15 *SOLD*Fox Level 3 Kit-Seattle WA

Applying 3m Tape to Weather Tech Visors

Discussion in '2nd Gen Tacoma Parts Marketplace (2005-2015)' started by rottenpixies, Dec 8, 2015.

  1. Dec 8, 2015 at 11:39 AM
    #1
    rottenpixies

    #1
    rottenpixies [OP] Well-Known Member

    Joined:
    Aug 19, 2015
    Member:
    #162178
    Messages:
    491
    Gender:
    Male
    New York
    Vehicle:
    2015 DCLB 4X4
    So I'm going to re-install my weather tech visors hoping that tightens up the seal for me and hopefully reduce some wind noise (since dealership said its "normal").

    Anyways, when I re-install them I want to put some 3m tape on there. Just wondering for others who have done it, should I put an inch strip of the tape on both sides of the top of the visors or just fold over a strip of tape right along the top of the visor? Any input on how to apply the tape to the visor to get the best hold and tighten the seal would be awesome..

    Thanks
     
    rottenpixies, Dec 8, 2015
    #1
  2. Dec 8, 2015 at 12:00 PM
    #2
    taczilla

    #2
    taczilla I intend to live forever; so far.... so good!

    Joined:
    Jul 18, 2012
    Member:
    #82874
    Messages:
    8,484
    Gender:
    Male
    First Name:
    Marc
    PEC, Ontario, Canada
    Vehicle:
    2016 RAM Rebel
    2012 TRD Sport - STOLEN! / 2016 RAM Rebel
    Wrong forum.
     
    taczilla, Dec 8, 2015
    #2
  3. Dec 8, 2015 at 1:03 PM
    #3
    Zac of all trades

    #3
    Zac of all trades FWP Fabrication Vendor

    Joined:
    Jun 9, 2015
    Member:
    #157073
    Messages:
    8,877
    Gender:
    Male
    First Name:
    Zac
    fwpfab.com
    Vehicle:
    2013 4x4 Locked DCLB
    886/5100s/AAL/UCAs/360 armor/RTT/295 17s
    Yes wrong forum.... should be under mods and tutorials...

    but you need (Good not Cheap) double sided 3M tape. It only needs to be applied to one side for both inchannel and the standard mount deflectors.

    InChannel deflectors need tape on opposite side that the glass will touch. Make sure you clean the channels well first and leave windows all the way up for atleast 24 hours to get a strong hold.

    Also search YouTube for videos. There are plenty of install videos on the internet.
     
    Zac of all trades, Dec 8, 2015
    #3
    rottenpixies[OP] likes this.
  4. Dec 8, 2015 at 1:12 PM
    #4
    rottenpixies

    #4
    rottenpixies [OP] Well-Known Member

    Joined:
    Aug 19, 2015
    Member:
    #162178
    Messages:
    491
    Gender:
    Male
    New York
    Vehicle:
    2015 DCLB 4X4
    Appreciate it. Trust me I felt stupid even typing this thread, but I know a lot of people here have used 3m tape and I wanted to make sure I did it effectively. Thank you very much for the response.

    I bought this stuff: [​IMG][​IMG]
    $15 Scotch Mounting, Fastening & Surface Protection Permanent Outdoor, Holds 5 lbs, 3M Scotch 4011 Exterior Mounting Tape, 1 in x 60 in, 1"x60"
    http://www.amazon.com/Scotch-Exteri..._60_img_3?ie=UTF8&refRID=0MW2CR8YJYXZDNRCV47Y


    That's specifcally what I wanted to know, is if I needed tape on both sides.
     
    rottenpixies, Dec 8, 2015
    #4

Products Discussed in

Scotch Mounting, Fastening & Surface Protection Permanent Outdoor, Holds 5 lbs, 3M Scotch 4011 Exterior Mounting Tape, 1 in x 60 in, 1"x60"
$14.29
To Top