1. Welcome to Tacoma World!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tacoma discussion topics
    • Communicate privately with other Tacoma owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

First gen manual trans question

Discussion in '1st Gen. Tacomas (1995-2004)' started by Kens04Taco, May 30, 2019.

  1. May 30, 2019 at 1:19 PM
    #1
    Kens04Taco

    Kens04Taco [OP] Well-Known Member

    Joined:
    Sep 11, 2016
    Member:
    #196991
    Messages:
    1,697
    Gender:
    Male
    Sunland, CA
    Vehicle:
    2004 PreRunner 4x4
    kangs and thanngs
    hey guys I’m in the process of building a fuse panel/electrical tray for a 2003 with a manual trans. Unfortunately I don’t have the truck with me so I was hoping someone could get me the measurement from the fire wall to the point on the slave revisor cap closest to the front of the truck. I’m planning on starting it right before the cap so it’s not obstructed. Thank you guys !!!

    Pic is basically what I’m doing but this is on my truck which is auto

    CDBDB1E6-5DA9-4F0D-863C-8E742745BA56.jpg
     
    GQ7227 likes this.
  2. May 30, 2019 at 1:35 PM
    #2
    AKsavanaman

    AKsavanaman Well-Known Member

    Joined:
    Feb 8, 2015
    Member:
    #148232
    Messages:
    441
    Gender:
    Male
    Lower 48 :( U.P MI
    Vehicle:
    01' Xtra Cab TRD, Kings, JBAs, Dakars and 295's on F5
    Kings, JBA's, Dakars, Prinsu Rack, ARB, Trail gear sliders... and rust
    You talking evap canister???
     
  3. May 30, 2019 at 1:39 PM
    #3
    AKsavanaman

    AKsavanaman Well-Known Member

    Joined:
    Feb 8, 2015
    Member:
    #148232
    Messages:
    441
    Gender:
    Male
    Lower 48 :( U.P MI
    Vehicle:
    01' Xtra Cab TRD, Kings, JBAs, Dakars and 295's on F5
    Kings, JBA's, Dakars, Prinsu Rack, ARB, Trail gear sliders... and rust
    IMG_20190530_163626208_HDR.jpg
    Top right cap is for the clutch res... Just trying to see where you need the measurements from
     
    Kens04Taco [OP] likes this.
  4. May 30, 2019 at 1:49 PM
    #4
    AKsavanaman

    AKsavanaman Well-Known Member

    Joined:
    Feb 8, 2015
    Member:
    #148232
    Messages:
    441
    Gender:
    Male
    Lower 48 :( U.P MI
    Vehicle:
    01' Xtra Cab TRD, Kings, JBAs, Dakars and 295's on F5
    Kings, JBA's, Dakars, Prinsu Rack, ARB, Trail gear sliders... and rust
    Firewall to center of clutch res cap is 2.5" exact. 3 1/8" from driver side of engine bay to center of cap. 4.5" from top evap canister to center of cap. 7 1/8" from evap canister to firewall. 5 7/8" from brake booster to driver side engine bay. When I reference the evap can I mean the closest edge of the circular portion to the firewall...sorry I'm not sure what the actual name is.
     
    Kens04Taco [OP] likes this.
  5. May 30, 2019 at 2:22 PM
    #5
    Kens04Taco

    Kens04Taco [OP] Well-Known Member

    Joined:
    Sep 11, 2016
    Member:
    #196991
    Messages:
    1,697
    Gender:
    Male
    Sunland, CA
    Vehicle:
    2004 PreRunner 4x4
    kangs and thanngs
    You sir...are the shit! Thank you very much!!
     
  6. May 30, 2019 at 2:25 PM
    #6
    Kens04Taco

    Kens04Taco [OP] Well-Known Member

    Joined:
    Sep 11, 2016
    Member:
    #196991
    Messages:
    1,697
    Gender:
    Male
    Sunland, CA
    Vehicle:
    2004 PreRunner 4x4
    kangs and thanngs
    No he doesn’t have the evap in the engine bay but the 2.5 to center of slave res will get me where I need to be. I’ll start my mark 4 inches from the fire wall and that’ll give plenty of room
     

Products Discussed in

To Top