What Have You Done To Your 2nd Gen Tacoma Today?

See if whoever makes that light has a lense, would be a cheap route to start.

 

Those are Cali-Raised Ditch Lights. I think I want to use them as ditch lights, and replace them with lower intensity lights for the bed.

 

Clean upgrade

TOTAL CHAOS
WWW.CHAOSFAB.COM

 

Not a bad idea, and I don’t think Cali makes a lense anyway, they have their designated 18W 3x2 amber pods.

 

Could do some Rigid diffused lens lights and that should be better light dispersion and intensity

 

Bought and mounted the Smittybilt RTT, Hilux snorkel and just had the Coastal Offroad bumper welded up.

 

Looks really nice, you going for a bigger tire size?

 

Had a Jones Turbine 2525xl installed today. Sounds throaty but not obnoxious. No drone.

 

Panel is home made in my shop...... ABS....... EZ to work, cut with sharp knife and snap it...heat carefully and you can bend it, hold the desired position until it cools and it stays......this is the 4th or so version...made a few to mess with the layout etc....

VicoVation Vico-Power Plus Battery Discharge Prevention (BDP) Device for Parking Mode

https://www.amazon.com/VicoVation-V...ons&keywords=vicovation+vico-power+plus&psc=1

$10 Install Bay 89-00-9031 ABS Plastic 12 X 12 X 1/8"

https://www.amazon.com/dp/B0007WTF0...91f1-475e3f4e3ced&ie=UTF8&qid=1539030401&sr=1

 

made it in my shop (dont think big fancy)

$10 Install Bay 89-00-9031 ABS Plastic 12 X 12 X 1/8"

https://www.amazon.com/dp/B0007WTF0...91f1-475e3f4e3ced&ie=UTF8&qid=1539030401&sr=1

material is ABS ez to work, cut with sharp knife as in score and snap it....heat carefully and bend as you wish, hold it till it cools and it retains that shape....this is the 4th version, kept playing around with layout etc...fun project..finished off the console and dash gray /silver crap make over..

 

What about a sound bit?

 

Ran the Rubicon from Loon Lake to Spider Lake, and back, this weekend.

 

Revamped my aux panel. Went with a powertray panel this time. Rebuilt a new RTMR since my old one was trashed trying to remove pins/wires after the eBay seller installed the pins backwards.

I still have some work to do and tidying up but that’s enough electrical for one day.

 

Yep, have the same very happy with it. Had the non resonated on my Jeep prior.

 

I'll try to get one tomorrow or Wednesday.
TBH most exhaust clips don't really any vehicle justice.

 

Ive tried and further away seems to work better. The phone mic tends to pick up all the air it's pushing and the mic is not tuned for anything other than voices.

 

Ya I know, just curious, I hate my jetson stock setup, but don't want a fart box like those stupid hondas

 

This.

 

This wasn't today, but the past week worth of goodies.

• BP-51 suspension with extras
• 4.88 gearing
• ARB front locker
• Air compressor, switch pro, dual batteries and electrical all installed
• Prinsu roof rack with Baja Designs 40" S8 light bar
• Total Chaos LCA skids and UCA's
• Safari snorkel
• SCS F5 wheels
• 315/75/R16 KM3's

A quick summary of Phase 1 so far. Phase 2 to begin in a few weeks! I'm working on a build thread as well now that things are moving.

 

Just a suggestion, but you could probably clean up those two wires with fuses by only using one larger wire with a fuse and mounting a distribution block on the tray.