What Have You Done To Your 2nd Gen Tacoma Today?

https://www.tacomaworld.com/threads/the-torque-spec-guide.318116/

 

Ah, thank you!

 

I have a solution. Check out the thread below for some pictures. The bracket I sell will place the plate right below your tow bar, allowing complete function of the bar. You do not need to drill anything, it uses existing bumper cover bolts and installs in about 5 minutes.

 

Here is my routine. I leave the truck running, just so I know if I am affecting the operation of the vehicle and also because the engine heat helps to dry everything out. I used DILUTED Simple Green and liberally coat the engine and engine bay. I give that 5 minutes or so to work, then I use a soft bristle brush to gently clean all the nooks and crannies. Then I rinse with water and look to see if there are any places that need a bit more attention or a second round of cleaning. Then I get the 303 Protectant out and liberally coat the engine and engine bay. I use some microfiber towels to mop up any excess puddles and to touch up any spots that need a bit more shine. Start to finish, not counting the time to get all the supplies together should be about 15 minutes and the results should look like it did when it was brand new.

Go for it Chad. If you are apprehensive then go at it slow. I see videos of these trucks submerged over their hoods in water and the engine still working so the little water you will be applying should not phase it a bit.

 

That looks great, but still not what I need. I am looking for a quick release/removal of a plate ( for winch, etc) I found CURT hitch license plate holder on Amazon, will see how it goes.

 

My mistake, I didn't realize you were adding a winch to your set-up.

 

I did not either until recently

 

I see you were a victim of the "black" trd stubby antenna turning gold

 

Good Friday? No GREAT Friday:

https://www.youtube.com/watch?v=D7V_ayDX2U0

 

Paid off my 2013 DCLB.... now saving for this: 2017 4Runner Off Road premium with KDSS sitting on Kings and sliders

 

Check out this thread. Maybe this will interest you:

Cascadia 4x4 "Flipster V2" - Winch License Plate Mount (15% off)

@jeeper

 

After almost 28 years, I've pretty much healed up. She keeps them in a silk bag and lets me fondle them once in awhile.

 

Finally did the center cap mod. Thanks to @NYCO for posting how to, and FN Wheels for send out the missing hex screws for the caps. TRD caps came from Toyota of Daytona via Amazon.

 

Haven't read all the way through yet but I've used a cold chisel at the base of a filter to tap one off. You need to be VERY careful you only get a bite on the filter, but this has worked several times for me, mostly on old tractors and work trucks.

 

@ACEkraut makes a wonderfull solution!

 

Picked up this hood for 100bones off clist (it had sever hail damage) Had my buddy fix it and installed it today! I now have a non scoop super white hood up for grabs from an 09.

 

We went on a hike

Me thinks me need somma that high clearance action...
This is the actual level image

 

Added some new shoes, 285/70R17 on raceline assaults.
http://imgur.com/IQG70lR
http://imgur.com/iyQFqBe

 

Got my cap installed today! ARE CX. I can't wait for Not-Winter (there are only two seasons in north-ish Canada, winter and not-winter) to go canoeing and camping! If anyone notices, there is a bit of damage on my bumper from backing into a tree a while ago.

 

This was my solution
https://www.tacomaworld.com/threads...gen-tacoma-today.6499/page-5907#post-14876357