What Have You Done To Your 3rd Gen Today?

Getting prepared for gusset-palooza next weekend by getting the cam gussets welded up. Will be doing cam (obviously!), spindle, and coil buckets. The cam is the only immediate need (had one tab tearing off, and found another pushed flat), but figured might as well do the others since part of the work would have been done anyways.

 

I did a hand wash, rinse, McKees 37 Hydro Blue, and dried my truck off today. Easiest way to wax/coat a truck there is. Done it this morning at 7am when it was 50 degrees with a 12mph south wind. I would venture a guess and say that is the last wax/coating I'll put on my truck till next spring.

 

Looks awesome! Considering the same. What setting are the coils on? How much of lift from stock?

 

Thanks again. Glad you're liking the new camera. I guess I didn't completely make my self clear. When I was asking about the 3rd gen I meant the camera , not your truck . I've seen a V1P and V1P 3rd gen and it looks like the top of the two cameras are different and I believe would require a different mount. I wasn't sure if the Shapeways dashcam to gopro mount you have would fit both, that's why I was asking. I want to use the gopro mount on the windshield and it may make a difference in what camera to get based on whether it will fit that mount with an attachment you got or not. The 3rd gen camera looks a little better but not sure how I can mount it if the attachment won't work that you got.

 

Thanks

 

I'm sure it is. I've just never taken anything apart on the inside of the truck like lots of other people have. May brave it at some point.

 

I paid about $200 more than Amazon but that was installed.

 

Omega AH300BLK 3 Bell Steel Train Horn (Black)

Omega AC15 12V 1.5 Gallon Air Compressor https://www.amazon.com/dp/B003GLOHTK/ref=cm_sw_r_cp_apa_i_0LibCbY06FSRS

 

Before the muffler

 

You have a link or exact part number for this. Yes so stupid this did not come with technology package. Only offered on TRD PRO.

 

https://www.tacomaworld.com/threads/bilstein-6112.421995/page-91#post-19277443

 

Is there a noticeable exhaust smell with rear cats removed?

Did you drive it enough today to tell any difference in power?

 

I installed Christmas lights

 

With this new one
Cllena Dual USB Port Charger Socket Quick Charge 3.0 & 2.4A for Toyota

$20 Cllena Dual USB Port Charger Socket Quick Charge 3.0 & 2.4A for Toyota

https://www.amazon.com/dp/B07FD2Z6GF/ref=cm_sw_r_cp_apa_4OkbCbGA9KMGR

 

Threw on a set of @SCSPerformance SR8’s yesterday

 

Good fit on the seat covers.
Do you have a link for them?
Thanks.

 

Like I stated before, these are cheap, but functional. The front seats were really tight and I heard a couple stitches pop when pulling them over. I am not promoting these covers, use at your own risk, but they have been good on the Rav4, so we will see about this set.

$36 FH Group Full Set Cloth Car Seat Covers , Universal Fit combo, Low Back Front Seat Covers, Airbag Compatible, Split Bench Rear Seat, Washable Seat Cover for SUV,Sedan,Van Orange

https://www.amazon.com/FH-Group-FB0...ANGE-COMBO&dpPl=1&dpID=51G1-dOPiGL&ref=plSrch

 

Installed Cali Raised sliders and a 30" led bar behind the front bumper.

 

Ran it solo. It sucked but needed done and no flights available the day I needed to be there. Ran from Portland Or to Dallas TX and back via Grangeville Idaho.

 

What the piss.. Burning Bread lol